Common Rail Wiring Many older model railroads use Common Rail wiring because they were initially wired to operate with electrical toggle switches. Conversion to DCC is possible with Common Rail, but it is not recommended. Whole layout common rail is a method of wiring layouts where power districts and their boosters are electrically connected using a common rail or common power bus return wire. Whole layout common rail wiring is a disadvantage when it comes to detection systems since detectors cannot independently monitor whether zone power is on or off so they can't tell whether occupancy detection is working in ...

As has been noted in other articles, most model railroads require a power bus which uses 10 - 12 gauge solid copper wire.  This power bus is routed around underneath the layout, providing an efficient path for the layout's power needs.The command station/booster is connected to the two wires of this bus; one wire uses black color insulation and the other uses red color insulation.  The rails of the layout are then connected to this power bus at six foot intervals, at minimum; denser track areas require more such feeders.  For an individual command station/booster or for a booster by ...

My layout is the Apex & Hypotenuse design, from the Atlas design. I was wondering where would you suggest I wire the AR1. We remember this layout design, if for no other reason than its ingenious complexity. This railroad initially appeared in the Custom Line King Size Plan Book - H0 Railroads You Can Build, originally published by Atlas Tool in 1966. This book was yet another collaboration between the late John Armstrong and illustrator Thaddeus (Tad) Stepek. This railroad must have required a certain level of dexterity by the operator since the reversing segment is actually two different return ...

Direct Home Layout Wiring Digitrax strongly recommends direct home wiring where each power district and its booster are electrically isolated. This method of wiring has safety advantages and makes troubleshooting problems easier. In addition, direct home wiring makes detection work more prototypically. With direct home wiring, the BDL168 can determine and indicate whether any of its 4 zones is powered or not (possibly short-circuited) even when there is nothing on the rails in the detection sections. The BDL168 factory-set logic causes the detection sections to show "occupied" if the associated zone's power is off (because in this case, detection is ...

Track voltage on DC (analog) layouts can be measured from rail to rail.  However, with DCC layouts that use direct home wiring as recommended by Digitrax, this method of measurement does not work with most voltmeters.Track voltage (output from the booster to the rail) on DCC layouts with direct home wiring can be measured as follows:1.     With the system powered up and with the TRACK STATUS LED on, use your throttle to select the analog address 00 and set the speed to 00.2.     With a multimeter set to the 20 volt DC scale, measure the voltage from RAIL A ...

  The most common problems on the layout that will impact your DCC system are electrical short circuits. If you find that you cannot get the Track Status light on your command station to come up, or there are numerous beeps from the booster, then disconnect one of the Rails from the booster and the problem should be apparent. There is an electrical short in your layout wiring. The quarter test is the BEST diagnostic tool that you have! With your DCC system up and the Track Status ON, create a short circuit across the rails of the layout every ...

What's the best method to handle structure and street lighting with a DCC layout? If I put in bus wiring for my lighting can it interfere with the DCC signal? Unless you have stationary decoders that control the structure and street lights, there is no need for connecting these lights to your DCC wiring. In fact, doing so will add additional power consumption without any of the advantages of command control. These additional power consumers take away available power for your locomotives, controlled cars and stationary decoders. Should I use a completely different power source like an old power pack? ...

I am building a layout that will have two completely separated track plans; not connected with each other by any track. I am running one layout with a Super Chief that has one AR1 reversing controller.  I would like to run the second layout with the same throttle. It will have a reversing loop, as well as a turntable.  I have thought that I could run the second layout with a booster and a couple of AR1s or PM42.My questions is, will I have any problems with the reversing loops, especially if one on each layout is triggered at nearly ...

I have a 4x8 layout, I want to run 2 or 3 trains. I will operate the layout by myself or with possibly one other operator. It's a really basic operation. Which Digitrax set is best for me?The Zephyr Xtra Set will probably do what you want. You will need the Zephyr Set and mobile decoders for the locomotives. You can connect up to 20 throttles to your Zephyr Xtra Set so that adding another operator is as simple as plugging in another throttle. You can also use one or two smooth DC power packs as throttles for additional operators to run trains ...

1.  Install BDL16 series occupancy detector(s).  BDL16, BDL162 and BDL168 occupancy detectors can be used together on the same layout.2.  Add RX4 transponder receivers to the zones you want to set up for transponding. (You won't need to cover every detection section on the railroad for effective coverage and reporting. Some areas will be detection only sections while others will have full transponding as needed.)  Use either two RX4s with your BDL168 to set up 8 transponding zones or use one RX4 if you only need 4 transponding zones.3.  All current production Digitrax decoders are transponder equipped. If you have decoders ...

We are a LARGE club layout. We have several reversing districts, 25 operators and run 30 trains at a time. We want computer control, turnout control, signaling. You name it, we've got it. What equipment do we need to run this layout?You probably need the Super Chief Xtra Set with additional throttles, boosters, mobile & stationary decoders & detectors.A typical HO layout of this size would need approximately 5 boosters & power supplies to provide enough power to run 30 engines. The DCS100 command station/booster will be one of these boosters so; you would need 4 additional DB150 series boosters. You will ...

Reducing Sensitivity for Outdoor Layouts Outdoor layouts may require reducing sensitivity to allow for more accurate occupancy reporting through the BDL168. Resistors are connected between the detection zone and the zone common from the blue connector to reduce sensitivity. A 1KOhm resistor will reduce the sensitivity by 1/2. A 100 Ohm resistor will reduce sensitivity by a factor of 10.

Q:  Which decoders work on Transponding layouts?A:All DCC decoders can be used on transponding layouts. However, only those decoders with Transponding capabilities turned on will issue a report each time they enter or exit a Transponding Zone.  All current production Digitrax decoders include transponding.Transponding can be added to any decoder by installing a TL1 or TF4.

If you want to use Transponding for bi-directional layout communication and are using Digitrax LocoNet, you will not have to add any "feedback bus" since this is already incorporated into LocoNet's design! If you want to use Transponding with a non-LocoNet system, you will need to add LocoNet. Non-Digitrax control systems require a separate feedback bus for the layout to achieve more limited types of bi-directional communication anyway so, you can simply add LocoNet instead of that feed back bus.

I was planning on purchasing the Digitrax Super Chief Radio 5 amps but several members in the club told me to buy them Super Chief Radio 8 amp for my HO Layout.  They said you will need the power when you start expanding.Question:Is it ok to use the 8 amp version for my HO layout?Answer:Yes it is fine to use 8 amp Digitrax boosters on your HO layout.  The choice between 8 amp and 5 amp command station/boosters, it is a question of how much power your railroad is likely to consume on your railroad as it is built today.  ...

Q: I would like to know about SE8C and signals on non-DCC layouts. A:  The SE8c is a signal driver for your layout. You can operate signals manually with any LocoNet Throttle and Command Station. Or, in your case, the SE8c can drive signals automatically with detection and compatible computer software such as RailRoad & Co. or JMRI.You will need detection devices to identify the presence of trains, a computer interface such as the PR3, a computer program supplying the signaling logic and the SE8c driving the signal heads themselves. Note that in a LocoNet environment, the SE8C supports detection: DS01 ...

Q: Can you have two command stations on the same layout? A: No. If you try and run with two command stations you will experience what we usually refer to as "shocking, horrifying results." Two command stations on a single layout is often a problem with modular layouts. You can disable the command station capability in Digitrax Command Station/Boosters so that you can use them as boosters only to add more power to your layout.For the DCS100 to disable command station mode:1. Set Op switch 2 to "c" 2. Set Op switch 5 to "t" 3. Set it to auto ...

I have a small switching layout, I am interested in low-end speed control and want to control turnouts from the hand held. What components do I need?All Digitrax command staions offer excellent low-end speed control as long as you are using decoders capable of 28/128 speed step operation.  Low speed performance will also be affected by how you set up the CVs in the decoder to define how the specific locomotive will respond to system commands.  Remember that installing a DCC deocder will not automatically improve the operation of your locos, you will need to first make sure they run ...

Model railroad layout signaling is just as complicated as real railroad signaling. This is an example of how signaling might work on a small oval layout.  Once you understand how the signals work together in a simple setting, you will be better equipped to tackle signaling on your layout. The layout is a simple oval with a passing siding. Here are the locations of the individual signals: This railroad has four Absolute signals, two Dwarf signals and two Permissive signals.The four Absolute signals and two Dwarf signals protect not only the main line & the passing track but also the two turnouts ...

Q:  Can I use non-Digitrax decoders on a Transponding layout?A: Yes.  If you want to add transponding to a decoder that does not have the feature, add TL1 or TF4 to the decoder.  Some non-Digitrax decoders that use supersonic features are not compatible with transponding unless you switch off the supersonic feature. Digitrax supersonic decoders are compatible with transponding and can be used in supersonic mode while transponding.

To stop everything on the layout, press the PWR Key followed by the N - Key while the track power is on. This will turn track power off and will cause all locos to stop. Press the PWR Key followed by Y + Key again and the locomotives will start running again at the same speed they were running prior to STOP mode. To exit PWR mode, press the PWR Key or the EXIT Key.

Can I still operate a non-decoder equipped locomotive on my Transponding layout?Yes! Transponding will not affect operation of an analog loco (one without a decoder) on address 00. The analog loco will not transpond since it is not transponder equipped.

Q:  I am the only operator. There will be no others. I wish to use block detection for signaling. However, I find that I cannot use the BD4s in the way I thought they could be used. My question, must I divide my simple layout into blocks (which DCC says you don't really need) in order to use the BD4's and SE8C together? A small basic layout can be operated in the DCC environment without dividing the railroad up into power districts.  In this scenario, you will use one command station/booster to power the entire layout. As your power consumption ...

Am planning a 4 district layout with a Super Chief set. Can I serve all 4 districts with it using circuit breakers for each district? If not what do I need?In this case, the PM42 quad power manager can be used to give you circuit breakers in each of the 4 sub-districts.

1. The UP5 Universal Panel is designed for mounting on the fascia board of the layout. Cut a hole approximately 2.5” W x 1.5” H in the fascia board. Insert the UP5 through the hole with the face plate on the front of the fascia board. Attach the UP5 face plate to the fascia board with four #6 screws. Note: The UP5 uses the black screws to mount the front fascia plate.2. Connect the UP5 to LocoNet using pre-tested LocoNet cables. There are 2 LocoNet Jacks located at the back of the UP5 board for connecting LocoNet devices on your layout. ...

I have a medium/large sized layout with a reversing district. I want to operate 6-10 trains with several operators. I am interested in turnout control, prototypical consist operations and signaling to be added later. I might want a computer added later, too. Which components do I need?You will need a Super Empire Builder Xtra or Super Chief Xtra with additional throttles for the operators and an additional DB150 booster or PM42 for the reversing district. You will also need at least one additional DB150 to provide enough power to run 6-10 trains in N or HO. You can choose and Digitrax ...

Do I need an additional booster if I run isolated sections through a PM42 or can I use one Zephyr?  This is a small layout design (5X9) and looking to make it as simple and safe as possible.This is really a question of how much power your railroad requires.  You don't state what scale you are operating in, so a 5x9 in H0 might only have three or four locomotives, while a 5x9 in N-Scale might have fifteen or twenty locomotives.Initially, you will be making an estimation based upon your power requirements and the output power of the 2.5 Amp ...

  I have an "M" shaped 250 square foot layout with 500 feet of track and twelve locomotives. What Digitrax equipment would I need? You don't say what scale this railroad will be modeled in, which is important since the locomotives in smaller scales draw less current than larger decoders. However, for purposes of estimation: Twelve Locomotives. Each locomotive is going to draw, at the very least, 5 MA for the decoder. If it has LED lights, then it will typically draw 15 MA more; conventional light bulbs will draw 50 MA. A typical H0 locomotive will draw 600 MA ...

I am a 'newbie' to model railroading.  I have a 10' x 10' room put aside for my layout which will be basically a U or horseshoe shape going around three of the walls.  I am using Atlas code 55 in N scale. Since I'm starting from scratch, I want to do it RIGHT and that is why I've decided to buy DCC straight away. I want to run a maximum of 4 trains at once. I would like the capability of having two users (drivers) operating at the same time, but I want to manually set turnouts. I will ...

Train detection and the related signaling can be a complicated affair. However, it becomes easier if you analyze things and break them down into their component blocks. The whole idea is to protect trains from each other, regulating their movements by the use of signals which tell train crews what to do or what to expect. Train detection identifies which segments of track are occupied by a train. For the real railroads, track detection sections can be very short (such as at track junctions) or very long (such as in rural environments). Train speed and frequency of trains are also ...

The SFX004 can be used in a stand alone configuration as well. In these situations just connect pins 9 and 10 to the track and address the device normally.

Individual signal heads are driven from connections marked DRV1 - DRV8. Although these are typically connections to individual signals, they can serve more than one signal as necessary. The ID Button is used to set the individual SE8C board ID. If using more than one such circuit board, each must be assigned a unique number so that the system recognizes it. The Option Button is used to customize the SE8C. LocoNet Jacks provide a data channel for the SE8C.

The DT400 can be connected directly to the LocoNet port of your command station or to any Universal Panel of your LocoNet system.

You can simply add a TL1 or TF4 to locos with decoders made by other DCC manufacturers. In the case of some supersonic decoders made by other DCC companies that are not transponding compatible, you will need to turn off the supersonic feature when you want to use transponding. Digitrax supersonic decoders are compatible with transponding and can be used in supersonic mode while transponding.

I have a 4x8 H0 scale layout.  I'm 13 years old and REALLY thinking about switching to DCC, I need to know really fast because I want to ask my parents to get it for Christmas.You wouldn't know by looking at those who edit the Tech Support Depot, but there actually was a time when we too were thirteen, and just starting out in model railroading.  In many ways, we still are thirteen years old; we just can't move as fast.  Consider this photograph from our youth: This little bit of ancient model railroad history dates back to the 1950's, ...

At first glance, the typical switching railroad would not seem to be a good candidate for DCC operations. Yes, there may be only one locomotive on many of these railroads, but that locomotive can still benefit from DCC. By adjusting the starting, mid-range and maximum speed values of this locomotive, you get very good slow speed control, perfect for the switching railroad. And, of course, if you add a second locomotive, then DCC becomes the clear choice because you are not longer having to throw toggle switches just to move around the yard. The DCC environment also gives you turnout ...

Since each system, no matter how large, needs only one command station, you need only one WTL12 (or other Digitrax Command Station) performing this function. Any additional WTL12s must be converted to a booster by following the startup directions described below: Disconnect the power from the WTL12 unit Press and Hold the VOL- key Reconnect the power while continuing to hold the VOL- key Release the VOL- key The WTL12 is now configured as a booster/throttle only.  The power button will be lit up red on the right side. The command station determines the total number of locomotive addresses your ...

Single 3/5/8 Amp AutoReversing DCC Booster with up to 8 Amps of power total. Opto-Isolated for layouts with common rail wiring

Direct Home Wiring: A wiring system where the DCC booster powers each rail via an individual wire.  Each booster is wired to it's own track power section and there is no electrical connection between boosters. This means that each power district is double gapped and is connected to it's own booster.  The boosters are in turn connected via LocoNet to the command station providing one source of commands for the entire layout.Digitrax recommends using only Direct Home Wiring for all Digitrax layouts. Non command control layouts typically use common rail wiring as part of their control method. This means that one rail ...

I'm helping a friend rewire an existing layout from analog to digital. You might be familiar with the layout, it is the original Clinchfield layout that Model Railroader built back in the late seventies, believe it or not. The layout, of course, is blocked for analog through DPDT switches which have been eliminated. I was able to repair the wiring back to original using the drawings that MR printed. The layout uses common rail wiring, this is what I have to work with, and to rewire using home run wiring would be a MAJOR rework, not doable. I was able ...

Here are some terms that you might find useful as you work with the BDL168. Direct home wiring is a layout wiring method where each power district and its booster is electrically isolated. The track within each power district uses a "common return" wiring method for occupancy detection and/or power management. Direct home wiring is the wiring method recommended by Digitrax for safety reasons & also because it makes detection work more prototypically. Power district is the power wiring, track, components and equipment attached to that wiring, driven by a single properly isolated booster. The track for a power district ...

Before sending your Digitrax Command Station or Booster in for repair try these simple steps to see if you can “bring it back from the dead” and save a possible trip to the repair shop.1. Nothing is respondingIf there are NO LEDs lit on the front panel of the Command Station or Booster: Check the power supply to the unit to make sure that it has not been knocked loose in the power socket and that the socket is powered. Check the connections from the power supply to Track A and Track B connections on the front of the unit ...

I still don't understand the bus stuff. Wires come from the command or booster and run under the track layout and have feeders coming off. I understand these feeders connect to the track. Where do you connect the wires coming from the power source? (ie: Zephyr) Is there a particular place on the track layout it is to connect to?The power connection for the command station and boosters is directly between the power supply and these units.  It is not connected to the track!  Please see the diagram below: In this case, the Zephyr is the Command Station and Booster ...

LocoNet typically supports a total cable length of up to 2,000 feet with no two devices connected by more than 600 feet of cable. LocoNet wiring is totally free-form. We do not recommend looping LocoNet back on itself.Making your own LocoNet Cables is simple and cost effective. LocoNet wiring consists of readily available wire and connectors. LocoNet uses flat 6 conductor wire and 6-pin RJ12 connectors. This kind of wiring is typically used for telephone wiring. Most Digitrax dealers can make up LocoNet cables for you. If you plan on wiring a large layout, you may want to invest in ...

LocoNet is Digitrax's method of communication between LocoNet compatible devices on a model railroad layout.  LocoNet compatible devices are designed to work together on the network, and in some cases can also accept DCC commands from  the track, but often go beyond the scope of simple DCC train control.   LocoNet is a peer-to-peer Ethernet type multiple access network.  Because of its design architecture, it is very robust and powerful.  Layout implementation is simple and wiring is free form with minimal limits. LocoNet is designed to run an unshielded 6 conductor ribbon cable.  Digitrax recommends using flat, six-conductor telephone wire ...

In order to simplify our wiring diagrams, instruction sheets and general model railroad wiring, the following wire colors are suggested for wiring layouts and accessories.

Digitrax Complete Train Control By Zana & A.J. Ireland Digitrax Complete Train Control makes reliable, realistic train operation and simplified layout wiring a reality. Digital Command Control is incorporated within the Digitrax system to let you control multiple trains independently on the same section of track without blocking. In the real world, engineers control the speed and direction of real trains. Engines operate under their own power independent of the track. Each engine has its own motion characteristics like how fast it speeds up (acceleration) and how long it takes to slow down (deceleration). A locomotive's performance is influenced by ...

One of the basic problems encountered with command control systems is when things simply are not working.  Period.  Even after vigorous exhortation on your part, and perhaps even some enthusiastic train table banging, nothing is running.  At this point, it is time to gather your wits and your patience for a debugging session.   The first step to determining how to proceed is to determine if the problem with the electronics or with the layout?  The tendency is to blame the electronics, after all it is a black box.  But don't jump to conclusions so quickly! Be patient and follow the ...

Connecting a PS2012 DC power supply to an “Advanced Booster”  DCS240 and sharing with older Command Stations and Boosters: The 2016 US DOE external power supply Efficiency requirements effectively require using DC input power and supplies for new-design products including our Advanced Command Stations/Boosters.     Digitrax does not recommend sharing a suitable DC supply for an Advanced type unit like a DCS240 with older Legacy Digitrax Command Stations/Boosters designed to run on AC output transformers. This is because the common Booster Ground (typically pin 4’s) and negative power return wires have a diode offset in non-Advanced (AC input)  units ...

Although this is a simple railroad, it will have some advanced features. When the railroad's sectional modules are first assembled, the electrical connections are simple. The railroad will be controlled with a DCS50 Zephyr, using a PM42 Power Manager for short circuit protection. One section of the PM42 will control the inner oval of track, a second section of the PM42 will control the outer segment. This is done so that if a train derails on one loop, the train operation on the other loop will not be affected. Because the DCS50 is rated at 2.5 amps, the PM42 must ...

The PS615 is the Digitrax recommended power supply for the DCS240 in 5 amp mode.  For operations at 8 amps the PS2012 is the recommended power supply. When using the PS2012 special wiring considerations need to be used when powering both the DCS240 and legacy boosters from the same PS2012.  Leagacy boosters are defined as the DCS100, DCS200, DB150, DB200 or DB100.  Please see the separate article “Powering your DCS240 with a PS2012” and the additional notes below. The DCS240 may be powered either using the barrel plug connector or the screw terminals labeled “+” and “- “. The barrel ...

By Zana & A.J. IrelandThis clinic is titled Digital Command Control: The Wave of the Future. Recently, I was asked the question: "DCC has arrived and is the technology of today, everybody's using it so, why don't you change the title of your clinic?" My answer is that digital command control is still evolving rapidly. Today's digital command control is moving beyond the basic NMRA DCC Standards and RPs to encompass many new technologies that will compliment and enhance the basic things we can do with the track format defined by the NMRA. It's an exciting time for model railroaders ...

By Zana & A.J. IrelandThis clinic is titled Digital Command Control: The Wave of the Future. Recently, I was asked the question: "DCC has arrived and is the technology of today, everybody's using it so, why don't you change the title of your clinic?" My answer is that digital command control is still evolving rapidly. Today's digital command control is moving beyond the basic NMRA DCC Standards and RPs to encompass many new technologies that will compliment and enhance the basic things we can do with the track format defined by the NMRA. It's an exciting time for model railroaders ...

Fortunately, most DCC railroad wiring is very simple and easy to install. One critical point for any DCC system is power consumption, how much power an individual Booster is able to deliver. The available power is measured in terms of Amperes or Amps. The higher the Amp rating, the more power is available to run your layout.Amps have often been compared to water pressure in a pipe. When the pressure is low, turning on one faucet will draw from that water pressure. As more faucets are opened, the water flow from each faucet drops. One solution is to turn off ...

The SE8C can drive position light type signals such as those used by the Pennsylvania Railroad and the B&O RR and the N&W RR. Leads from the signals can be soldered directly to the pads on the Signal Mast Base (the Terminal Strip Mounting Kit can also be used for interfacing your signals with the system.)You can use either common anode or common cathode signals.  We recommend that you use either all common anode or all common cathode signals on your layout for consistency in the set up procedure on your layout. If you are using the terminal strip option ...

Digital Command Control (DCC) has specific electrical requirements that must be provided for your layout control system to operate properly.Input PowerAll DCC systems require an external power supply.  Digitrax manufactures several power supplies for our command stations and boosters: The 3 Amp PS415 (the Zephyr Xtra power supply) The 5 Amp PS515 for all Digitrax 5 amp command stations and boosters The powerful 20 Amp PS2012 can be used for multiple 5 and 8 amp command stations and boosters  Additionally, the PS14 is available to power various other devices for your railroad.  Digitrax strongly encourages you to use our power supplies to insure satisfactory ...

There are many transformers and power packs that can supply input power for Digitrax boosters & command stations. Most regular DC train control packs do not have enough power to supply the full power potential of the a 5 or 8 amp booster, since they were designed to only run 1 locomotive in a blocked system. To get the full power potential of your booster, you must use a power supply that can supply enough power. Check with your local Digitrax dealer to see which transformers are available. If you are using a Zephyr Xtra, please use ONLY the power supply ...

Q:  What are circulating ground loops and magnetic induction loops?  What are their symptoms and how can I fix them?A:  Like a lot of things, when you get down to the details, there can be disagreement about certain matters.Consider that the Super Chief manual states:  "To minimize the possibility of radio interference, twist all conductors."  Yet, this database has an article that states to the contrary; please see the related article in question, which is linked below.  In this situation, it must be remembered that the original manual was written several years ago and the most recent update was in 2004 ...

Kato recommends, and Digitrax concurs, that the best DCC performance with the Unitrack turnout requires that you set each turnout to "Non-power-routing". Kato has offered a variety of turnouts in their H0 Unitrack line.381-2840 - LH, 490mm Radius, selectable operating mode with power or non-power routing.381-2841 - RH  490mm Radius, selectable operating mode with power or non-power routing.381-2850 - LH, #4, power routing only. * Some additional power feeds required for use with DCC 381-2851 - RH, #4, power routing only. * Some additional power feeds required for use with DCC381-2860 - LH, #6, live or insulated frogs, power or non-power ...

I have a DCS50  Zephyr system.  I'm having a great deal of problems with it when I try to run (2) loco's equipped with LOK SOUND and DCC decoders (by ESU).  What happens is that it cuts in and out 3 to 5 times on each revolution of the train. I see it cutting out on turnouts sometimes, but not on straight track.  And sometimes when the loco's are on a hard pull, like at a sharp uphill curve.  When they cut out it just isn't the loco's, but the entire railroad.With the addition of the sound electronics, power consumption ...

I have a large oval layout with a view divider down the middle. I have two Zephyr units, one on each side of the divided layout. I don't have separate power districts (do I need to?). Can I run both Zephyrs? What do you suggest as to wiring the two Zephyrs? The easiest thing would be to divide your railroad into halves, with one Zephyr located on each side of the view block. Both rails would be insulated at both intersection points with the viewblock. One Zephyr would be the command station while the other Zephyr would be used as ...

Q: I connect my DT400 to my DCS100 and it works fine, but when I add a DB150 working as a booster the DT400 stops working. What is wrong? A: A number of things may cause this, so you can use the diagnostic features of the DT400 to solve this problem. Experience has proven that the most common LocoNet problem is related to pins 3 and 4. By following this diagnostic procedure, you can narrow down to the source of the problem. Starting with DT400 without a battery [The throttle has no battery for this test to assure it executes ...

The Kelana Jaya Rail Line model is a DCC intense layout, using many Digitrax command control components to achieve the goal of training operators of the actual rail line. The railroad was built in the 1990's and many of the Digitrax devices used for the Kelana Jaya Rail Line model have been superseded with improved units. Components used for the Kelana Jaya layout: 28 Mainline turnouts 11 Yard turnouts 39 Tortoise switch machines 84 Dwarf signals (yellow/green, red/green, red/yellow) 38 Mainline block signals 38 Heavy duty SPDT switch relays Digitrax Components Used for the Kelana Jaya layout: 1 DCS 100 ...

Your DCS50 has two sets of DCC outputs. This means that you will be able to program decoders using one set of DCC outputs while the layout is running on the other set of DCC outputs. When you hooked up your DCS50 to the layout, you used the RAIL A & RAIL B connections to the track. Now we will use the PROG A & PROG B outputs to set up a service mode programming track.NOTE: The programming track is powered for programming only and cannot run locomotives. You will have to manually move your locomotive on to the track ...

Q:  Will Digitrax Transponding affect my existing boosters, track wiring or locomotive pickups?A:  No. Digitrax transponding is designed to be sued with DCC compatible boosters made by all DCC manufacturers, track wiring & locomotive pickups without causing any damage or operational problems with existing DCC track signals. Unlike other "bi-directional" systems, no high current spikes are used by Digitrax transponding that can cause problems with boosters and wiring. Digitrax transponding does not require the replacement or modification of existing control equipment or infrastructure.

Note: The connections illustrated above are for purposes of illustration. The NEM socket has six conductors which are arranged in numerical order from 1 - 6: Contact 1 - Motor Connection (orange wire) Contact 2 - Motor Connection (gray wire) Contact 3 - Track Pickup (red wire) Contact 4 - Track Pickup (black wire) Contact 5 - Forward Headlight (white wire) Conatct 6 - Rearward Headlight (yellow wire)

Wiring lighting without burning out bulbs on the first try. Need some info on which bulbs and boards need drop resisters installed and why. The new DH165 series have eliminated the mystery since they work with either LED's or with conventional lamps without adding resistors.

I have numerous locomotives I wish to convert to DCC. In order to spread the cost out over time I would like to install the connector/harness and add the decoder at a later date. Is it possible to buy the connector/harness assembly separately? Yes, there are several harnesses which are part of the Digitrax Easy Connect systemThis System Included the:DHWH - 9 pin to bare wires wire harnessDHDP - 9 pin dummy plugs to convert for analog operationDHWHPS - 9 pin to DCC medium plug short harness 1"DHWHP - 9 pin to DCC medium plug long harness 3"DHAT - 9 pin ...

Wired Mobile Decoder with SoundFX™+Accessory type functions for most HO scale Locomotives.

  Do you have a recommend wiring procedure for the 44-pin edge connector on the PM42 and SE8C?PM42, PM4, BDL168, BDL16, BDL162 & SE8C use a 44-pin edge connector. Connecting wires securely to this connector requires soldering skills. For connections to the 44 pin connector, Digitrax recommends using 16 gauge stranded wire. For all other soldering connections, Digitrax recommends 14 gauge (AWI) stranded wire for electrical connections on your railroad. 1. Use individual short lengths of 16 gauge wire to connect to the 44 pin connector. 2. Strip and tin both ends of the wire. 3. Bend one end into ...

Using Digitrax Decoders with AC Motors and Lionel Type E UnitsThis application note shows how Lionel users and other users of AC motors can use DCC to run their layouts.This example shows a wiring diagram for an AC universal motor with two-wire field coil. For this type of motor you must add a bridge rectifier to control the polarity to the motor's field coil.  This type of motor is found in AC locos built from the 1950s through today.Some Lionel type AC locos have motors with three wire field coils and an E Unit.  Half of the coil is used ...

This section discusses the installation of the physical wiring of the Texas & Southwestern. Underneath the completed Texas & Southwestern are various wires and cables which allow you to operate your railroad. Initially, seeing all these wires can be intimidating, but as you will note, they have been grouped and bundled so that identifying the individual wires is easy. There are two groups of wires under the railroad; one group, the power bus, delivers power to the tracks and to the stationary decoders that operate the track switches. The other group of wires is the black cable for LocoNet and ...

When I turn on the DCS240 and system, the DCS240 beeps 10 times and track power goes off. When I retry turning on track power, the 10 beeps occur again and the track power stays off. What is happening, and how do I fix this so I can run trains? The DCS240 actively scans for conflicting Command Stations at Power up, any time Track power is turned ON, and additionally about every 2 minutes.  If another Command Station is detected the DCS240 will issue 10 long beeps and the Track Power is turned off.  The DCS240 will not allow track ...

I've recently purchased a DCS50 system to run my HO trains. Since I'm new to the hobby I'm throughly confused on what parts I need to wire my 4 x 8 foot track to my control box. How many feeder lines do I need and what size do you recommend, and how do I hook these up to my control box? What size does bus wire do I need and how do I connect all this to my system? So far, all the articles just make recommendations general terms without specifics. I have purchased 2 terminal clips but have yet ...

This article stops in a strange place??  We need to find the rest of it and split it up into meaningful chunks.  Also needs meta stuff Troubleshooting in General:Regardless of the guides, manuals, tips, suggestions, experts or whatever, troubleshooting can occasionally degenerate into a vast chasm of darkness and confusion.  It would be impossible to cover all the areas that have, can or may cause problems. This is a general guide to identifying and resolving problems with Digitrax Complete Train Control.  Keep Good Records:Although it may seem to be a pain while setting up your Digitrax system, keeping layout records ...

DCC Automatic Reversing SectionsVirtually all automatic reversing will fall into 3 categories with the wiring principles for all being the same:1. Reverse Loops2. Wyes3. TurntablesDCC has the ability to automatically reverse sections of track we call Reversing Sections while our trains are running and not affect the direction or speed of the trains. This is because we put a constant square wave AC current on the track and control the trains (locos) by sending messages to them (actually to receivers we call decoders) to tell them what to do such as start, stop, change directions, etc. . We are thus ...

There was an error In the BDL168 Instruction Sheet, Figure 6 on Page 19.  The LT5 diagram was incorrect.  This article shows the correct LT5 Detection Sections.  The current on-line version of the BDL168 Instruction Sheet has been corrected. Each BDL168 comes with an LT5 that will help you with layout wiring and troubleshooting for transponding & detection. The LT5 plugs onto the LED header connections of BDL168 and the LEDs on the LT5 light when detection sections are occupied. The status of power to each zone is also shown. In service, the LT5 is plugged in to one of ...

How do I Increase BDL162 Detection Section Threshold SensitivityThe BDL162 has Option Switch settings to control detection sensitivity. The factory setting is OpSw19=t for a threshold sense for DCC occupancy of approximately 22 Kohms minimum. Changing OpSw19=c will set the threshold to 10 Kohm minimum. See the BDL162 instruction manual for details on setting the Option Switches. These settings will accommodate most layouts, though there may be circumstances when a higher threshold is desired, for example, in a high moisture environment or with G scale operations outside.To raise the threshold even further resistors can be added into the wiring between ...

Q: I read in the February 2008 "Scale Rails" on page 11 that I need to add some "High Frequency Filter" gizmos on my layout to make my trains run properly. I have been using Digitrax equipment for 12 years, do I need to make these changes? A: We do not feel that this is necessary. With modern, well designed decoders, almost any combination of transmission-line ringing and other mismatch effects described in this article are completely filtered and ignored by the decoder. This is a superior solution rather than trying to design filters for unpredictable limiting cases of wiring ...

Here are several things to check if you are having trouble with the BDL168: Proper Wiring Be sure that you have NOT connected pin 11 to pin M, as this can prevent proper LocoNet communication. Check to make sure not wires are touching adjacent pins.  Follow the wiring diagram closely. Packet Reception Be sure the green ID LED is ON & is “winking” off about every 2 seconds. This means that correctly formatted DCC packets are being decoded from the left most (Railsync) pin of the RJ12 LocoNet socket. For DCC detection, the same DCC packet signal that drives the ...

Use a throttle to change the PM42's Option Switches 01, 02 and 09 as detailed in the PM42 instruction manual. The PM42's trip current threshold can be set at a value from 1.5amps to 12 amps. Always use the lowest possible setting, consistent with good operation and reliable short circuit detection and recovery. Higher current settings are not "better." We ship the PM42 with a moderate current trip threshold of 3amps so it will work on most DCC boosters and layouts with no changes.This is because some boosters cannot supply enough current with the track feeder resistance to reliably allow ...

In earlier generations of model railroading, the reverse loop (reversing section) was the bane of many model railroaders. As the rails of a track come back upon themselves, an electrical short circuit is created. In the analog control world, the solution is to use toggle switches and special wiring to allow the locomotive to move on to the next block. Electromechanical solutions relying on relays and track detectors can also be used to automate reversing on an analog layout. The wye is another example of a reversing section on a layout. One of the advantages of digital command control is ...

In response to questions about the differences among the DCC systems that are currently available from different companies, I offer the following comments & observations. You may have heard that all the systems are pretty much the same or you may have seen “comparison” charts in various DCC companies’ literature, in magazines or “analysis” on the Internet by “impartial observers.” Unfortunately, it is almost impossible to break down the system and company differences on a simple chart & the people who write the “impartial analysis” are usually not really impartial. As you read these comments, please keep in mind that ...

LocoNet System ArchitectureDigitrax LocoNet is a Peer to Peer local area network (LAN) designed specifically for model railroad operation.  System architecture is the biggest difference among DCC systems, the way the components of a DCC system communicate among themselves. LocoNet wiring is cost effective, flexible and expandable to accommodate almost anything you want to do with your railroad today and in the future.System ExpansionHere are some of the expansion possibilities available with LocoNet. With Digitrax LocoNet your DCC journey starts at the Main Station with your first “starter” set. From there, it’s up to you. You can add:  Mobile decoders ...

Photo Courtesy Kato, USA The DN143K2 replaced the earlier DN122K2 as a custom decoder designed for the Kato RDC in N-Scale. This is not a particularly easy installation and there have been some reports of problems with the headlights. Paul Lator has some experience with this installation, and this may be of help to you: "The wiring with the DN143K2 works well if you do not route the wires over the top of the seating in the RDC, rather completely disassemble the unit, mount the decoder in it's designated location then run the wires through the drive shaft tunnels. Place ...

Installation Notes: 1. Do not exceed the decoder’s 500mA total function output rating. 2. If you plan to use functions F1 (traditionally a green wire) or F2 (traditionally violet), the return, also called +Common or Lamp Common, should be made via a wire carefully soldered to the Common (or blue) pin indicated as shown in Figure1. 3. To use a function output with an inductive (coil) type load, you must install a kick-back suppression diode across the connections. If controlling a coil type load, such as an electromechanical relay or motor, shutting the device off can cause an inductive kick-back ...

Our thanks go to Digitrax operator Aksel Suarez of Chesapeake, Virginia for sending this tip on how to install a Digitrax decoder in the Walthers GP15, called by some prototype railroaders a "Geepette" or "Cheep Geep". Use a DH165A0 decoder to replace the existing light board. Remove the plastic clips that hold the wires to the light board. Once the light board has been removed, place a piece of electrical tape on the metal frame to isolate the decoder from the frame and prevent a short circuit. The wires on the locomotive to the motor and lights do not follow ...

Installation Notes: 1. Do not exceed the decoder’s 500mA total function output rating. 2. We recommend that the Blue wire, also called +Common or Lamp Common, be connected as shown. If you wish to omit the Blue wire in your installation, consult the Digitrax Decoder Manual for more information. 3. The head lamp should be hooked up using the Blue/+Common wire for optimal Digitrax transponding operation. 4. To use a function output with an inductive (coil) type load, see the Digitrax Decoder Manual for more information to avoid damage to the decoder. 5. See the Digitrax Decoder Manual for full ...

1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the shell to the frame so that you can reinstall correctly. 2. The DZ125 has 6” wires that you will solder directly to the appropriate connections inside the locomotive. The smaller size allows the decoder to be easily installed in a variety of locomotives. The bare ends of the wires are wired to the motor connections, power pickup connections and the lights according to this standard. Note: Avoid stressing the solder connections of the wires to the decoder board. If a connection is broken, carefully solder the wire ...

Do you have a reference for wiring Proto 2000 older geeps with a decoder (not necessarily sound)? We actually have several Life-Like Proto's sitting around for conversion to DCC, including an older GP-18, older FA's and such that date back to the days when DCC was just a twinkle in AJ's eyes. Overall, converting these locomotives will be fairly easy but there are a few things to watch for. Make sure that the decoder has enough capacity to match the current demands of the locomotive mechanism.  You must measure the stall current of the locomotive to determine this.   Make ...

1. Carefully remove the locomotive's shell from the frame. Notice the orientation of the circuit board inside so that you can install the decoder in the same orientation. (Figure 1) 2. Remove the 10 black plastic plugs from the lightboard that secure the wires to the PCB. There are 4 plugs (retainers) on each end and 2 on the side for the motor connection. Remove the red and black wires, carefully noting where each wire originally connected to the PCB. Remove the lightboard itself by pinching the black plastic release tabs and pulling the board up and off of the ...

Background The world is filled with places like Nemo Junction, a crossing between two railroads which is protected by a signal interlocking plant that also serves as an interchange point between these railroads. Cars destined for places to and from another railroad are exchanged at places like these. The interchange has been described as being the ideal model railroad industry because any type of car can be found there, heading toward places that are not on the model railroad itself. Nemo Junction is based upon a real place, a location in Illinois identified on the timetable of the Santa Fe ...

Problems occurring on most auto reversing sections are a result of improper wiring or gapping. Digitrax auto reversing units such as the PM42 or AR1 require a "hard" short which means there must be good current flow to both sides of the gaps, on the reversing section side and on the "normal" side. Our experience has been that over 90% of reversing section problems are a result of improper wiring or improper gaps. Another 5% is a result of improperly wired or configured auto reversing units. It is poor practice to put the gaps immediately behind a switch (turnout in ...

Q) You are offering a Loconet Repeater Module LNRP. Is it an RailSync Booster, too? There is no description in the PDF-File about this attribute. A) The LNRP boosts (and separates) the Railsync "Standard" outputs from the master command station ("Protected" Railsync), so if there is a problem with this separated "Standard" Railsync copy, the master Command Station is unaffected along with other devices like track boosters that need good Railsync copies. This boosted Railsync is also over-current protected and the LNRP will turn off an overloaded "Standard" Railsync and automatically retry re-powering, so when the fault clears the "Standard" ...

Hooking up the UP5's Power Supply (Optional but highly recommended to make sure LocoNet voltage is adequate to control large layouts)The optional power supply (PS14) can be connected to one or more UP and/or UR panels to provide additional power for LocoNet operation and for battery saving power to any Digitrax throttle that is plugged into any of the powered panels.1. Plug the PS14 into the DC jack located on the side of the UP5 circuit board.2. Connect the +Common point on each additional board (located between the two LocoNet jacks) to the powered board with 22AWG wire (Figure 2). ...

American Wire Gauge (AWG) is a U.S. standard set of wire conductor sizes. The "gauge" is related to the diameter of the wire. The higher the gauge number, the smaller the diameter and the thinner the wire. Typical model railroad copper bus wiring is AWG number 12 or 14. Connecting wire is often 20, 22, or 24. European color coded wiring practice often calls for "9" gauge wire, or approximately 3mm diameter wire. They also use smaller wire for runs from stationary decoders to individual devices. The smaller the diameter the wire, the more resistance; this means that a larger ...

The Kelana Jaya Rail Line model layout uses WinLok 2.1 running on a PC under Windows 98 to operate the trains, turnouts, signals and to use the feedback from the block detectors for train control. This equipment was configured and programmed to PUTRA's specifications by Dr. Hans R. Tanner of DigiToys Systems. PUTRA specified the following capabilities for the control system used for the simulation: 1. Run eight trains at once in any combination of automated or manual control. 2. Define specific routings and be able to assign automatically or manually any route to any train at the time the ...

The slip switch is a track element that has both a crossing at grade and also a set of movable points which allow trains to both cross another track and also change track.  The Crossing The crossing allows tracks to cross each other at grade.  The Slip SwitchThe more complex slip switch allows trains to both cross and to change tracks: In the schematic below, you will note that the slip switch is more compact than ordinary turnouts.  As a result, they are often found in high track density areas such as passenger terminals, where space is at a premium. ...

I have this N-scale Proto A/B unit. I went to install the decoder in the A unit to the headlight, its an LED. My question is that once it was wired up and place on the track, I hit my headlight function and the light lit up then burnt out. This is my first wired decoder I ever installed with a head light. Can you tell me how to properly wire the led headlight to the DZ123 decoder so the light doesn't burn out? In looking at the DZ123 Decoder sheet, it suggests that I check the Decoder Manual for ...

Installation: Figure 1 shows the general arrangement for connecting one or more LNRP's to configure a LocoNet based system for operation. Note that the LNRP's drive the power and Railsync signals on the "standard" LocoNet cable segments, so each LNRP should have a DC input of +15V to +18V at up to 250mA supplied on the side DC power jack. Note that the shaded cable connections are made from the protected network side connections of the LNRP units to the components that are on the "protected" or high reliability part of the System. The other solid cable connections are the ...

  This document outlines the power requirements for Digitrax LocoNet accessories.  To simplify wiring, Digitrax recommends providing individual power supplies for like accessories.  For example a power supply or power buss which only powers the PM42s.  A power supply or power buss used solely to power multiple DS64s.  UR9x and UP5 panels can be daisy chained provided adequate current is provided to properly power all the panels.  Through the use of individual power supplies, the chance of Ground Loops or sneak paths back to ground is minimized.  Using individual power supplies will also make troubleshooting much easier.  Many Digitrax LocoNet ...

Adding duplex radio, infrared or simplex radio to your existing Digitrax system is simple because of LocoNet.InfraRedYou probably already own a DT300, DT400, UT4 or DT402 series throttle. All of these are "InfraReady." These all come with two IR emitters pre-installed. All you have to add for IR operation is one or more UR90 Infrared Receivers to your layout. Most layouts require multiple UR90s because the infrared signal is line of sight. This means that your receiver will need a sight path to the throttles.Simplex RadioDigitrax throttles with an "R" at the end of the part number are simplex radio ...

Q:  We will be using your SE8C's for signaling. Should we use the SE8C to control our slow motion switch machines, or should we use your DS64s for that function? A:  Both products will do the job. How you plan to use them on your layout will help you decide which is better in your situation. Here are some things to consider in making your decision:The SE8C will drive 8 slow-motion switch machines while the DS64 will drive four. If you have a large number of switch machines in a specific area, the SE8C might be a better choice, since the ...

Q: My front and rear lights on a steam locomotive (hard wired decoder installation) are connected in reverse. When the locomotive is going forward, the back up light comes on. When the locomotive is going in reverse, the forward light comes on. Can I reverse the lighting effects though programming the decoder or must I disassemble the locomoitve and physically swap the wiring to the lights from the decoder. A: Yes, you can do this with using function mapping in any Digitrax decoder Series 3 or later. If you have an earlier version decoder installed, you'll need to re-wire the ...

Kato makes a Unitrack double-crossover, their No. 20210: Kato has advised us that this unit has four solenoids in its base, each operating one turnout point set. Connecting the DS51K1 to the red / black wire pair at the base of the track will damage the decoder since the four solenoids of the crossover will draw more than the rated current capacity of the DS51K1. If you are wiring the DS51K1 internally to this track segment, it is easiest to program each turnout pair to the same address; done this way, activating one track switch address will result in the ...

"I had two Proto 1000 RDC's that I wanted to convert. After opening up the first one, I did what I usually do, yanked out all the circuit boards and such, threw them over my shoulder and commenced to hardwiring the decoder into the unit. Everything went fine, and I took it with me to a friend's railroad to enjoy what I had done. After I got there and played a bit, my friend commented that wasn't it neat that the Proto 1000 series has wiring connections on the circuit board in the locomotive, making things considerably easier. Wiring points?" ...

This Atlas Snap-Track layout appears in the Atlas Model Railroad Company's book "Beginner's Guide to HO Model Railroading". It includes a reversing section which can be controlled with a Digitrax AR1. DC Control For DC operation, Atlas specified an Atlas Controller (for the reverse loop), two Atlas Selectors (to control eight track segments) and seven controllers for the railroad's turnouts. DCC Makes Things Simple With DCC, the wiring of this railroad is considerably simpler. Because each locomotive has a unique address, the section insulated gaps and the two Selectors are not necessary. Likewise, the Controller is replaced with the AR1 ...

From the start, the Texas & Southwestern was built with DCC in mind. The T&SW was built from the ground up by an individual with considerable model railroad experience, but an issue arose that defied explanation. The T&SW was meant to be operated with a DCS50 Zephyr, and the layout support structure was enlarged slightly to fit the Zephyr into one corner of the railroad. As it turned out, the cozy corner space for the Zephyr turned out later to be a bit too cozy. The bottom of the Zephyr has ventilating slots to help cool the unit’s electronics. As ...

Q:  How do I wire a double crossover? Each crossover results in a reversing loop. Should I use a PM42 or AR1? This is O scale (2 rail) if that would have any bearing on your answer. A:  Without a drawing to see how things are laid out, this can only be a guess, but a couple rules do apply. The reversing sections must be longer than the longest train. And there should be only one train in the reversing section at a time. It also seems to be a good idea to keep the reversing sections away from the ...

I have my Kato Switches hooked up to a standard switch panel with toggle momentary switches. Can I hook up the DS51K1 stationary decoder in addition to this wiring? In other words, if hooked up the DS51K1 to the Kato Switch Machine that was already wired to another source to throw the switch, would the momentary power damage the decoder when it is operated by the standard control panel? I would like to operate these switches via DCC and by the control panel. In this situation, it would appear that using a DS64 configured for Kato turnouts (solenoid turnouts) and ...

Q:  Can one decoder be wired to run two engines, such as an A-B unit that do not get separated? A:  Yes, as long as the current capacity of the decoder is not exceeded. We recommend that you check the stall current of both locomotives before installing a decoder that will handle both. Note that you can control two locomotives with decoders as a consist or MU lash-up so that you do not have to use a single decoder to control both locos.Issues we have seen with using a single decoder to run two locos together:1.  Make sure your wiring between ...

How do I set up the SE8C to control semaphores? Installing Semaphore Type Signals with SE8CThe SE8C can be set up to use its 8 turnout motor drive outputs to run 8 three-position semaphore (arm type) signals using slow motion turnout control machines (such as the TortoiseTM machines) as actuators. These 8 semaphore signals are available in addition to the standard 32 LED signal heads on the 8 signal control cables and occupy a separate semaphore address control range.The SE8C automatically sequences the three possible mechanical arm positions to match 3 aspects of red, green and yellow using a position ...

This note addresses the installation of an H0-Scale wired decoder into Bachmann Plus ABA F-7s; it calls for using a DH140, which has been retired.  Current decoders such as the DH123 or DH163 or similar wired decoders can be used. Just finished up doing a few HO Bachmann Plus F7's, ABA's to be exact. Thought maybe some of you might be interested in how the DCC conversion went on these.They are an easy conversion!1.  The full stall current for these ranged from 500-700 ma for each loco . I selected Digitrax DH140 for the A units and a DH120 for the B ...

We have a number of customers who are running Digitrax alongside their existing block detection circuitry. There are numerous block detection schemes and circuits, and we cannot cover all the variations here. Generally, it is necessary to isolate the block detector power supply and ground system of your existing block detector system from that of the Digital boosters. The most common detectors use "back to back" high current diodes to sense block current-draw. Detectors with "opto-isolated" or relay outputs will generally have no problem sensing current draw of a loco, etc., on the DCC current, and will signal the occupancy ...

Needs to be investigated  Z.I am looking at buying one of your Super Chief systems. My question is :- Do you have to carry a bus under the boards or could you use an adhesive copper tape on the top of the board .  My system will be totally new; layout size 10 foot 6 inches x 8 foot.  Model Rail DVD showed this.The core power bus of the railroad is an important component.  Remember, the Super Chief will be delivering either 5 Amps or 8 Amps of electrical power.  Your interest is to make sure that sufficient power readily ...

You'll need a few simple tools when you begin installing decoders: A soldering iron, preferably temperature controlled. Though many installations do not require soldering, you may still need to use a soldering iron to install extras like lamps for special lighting effects. Solder. A small screwdriver for disassembling your loco. Small diagonal cutters for cutting & stripping small wire. Tweezers to pick up small loco parts. Heat shrink tubing for protecting wire connections, this is better than electrical tape. 1. Read the instructions FIRST and PLAN your installation. Have the proper tools on hand. 2. Choose a locomotive that runs ...

The DB200+ is the 8 amp booster. It has NO command station capability. This booster was designed for adding power to layouts that run lots of locos and for large-scale layouts where power requirements are heavy.DB200+ Control PanelNOTE: DB200+ front panel graphics may vary from those shown here.  Internally the booster is the same. These instructions are written for both versions of graphics as well as the DB200+ OPTO optoisolated version of the booster. About the Green Jumper WireEvery DB200+ is shipped with a green jumper wire on the front panel Booster Terminal Plug connecting Synch & Ground or ‘Config ...

I have a Athearn HO Scale MP15 Soo Line and have installed a DH166 decoder. How do I get the rotary beacon to flash? Function Outputs on the DH166 The DH166 is set up at the factory to control six function outputs. The DH163AT is configured to control the forward and reverse lights on the locomotive through the yellow lead and white lead using Function 0 (F0F-forward yellow and F0R-reverse white) for directional lighting. Functions F1(green) and F2 (violet) are part of the harness for easy hookup. F3 and F4 are also available on the decoder board. These can be ...

I am trying to wire my new layout (N gauge) using the DS 64 with Peco switch machine PL10. The PL10 has four wires to be attached. My question is: Do I need to attach all four wires or just one set of wires? The PL-10 is a coil-type switch machine with double solenoids. One solenoid is activated to make the track switch throw in one direction, and the other is activated to throw it in the other direction. All four connections are required, with one for each solenoid being common and the other two being for the individual coils. ...

Once you have set up the DS64 to operate the type of turnouts you will use, the next step is to hook up the turnouts to the outputs of the DS64. Each type of turnout machine has specific requirements for wiring.Note: The DS64 is configured for either for solenoid turnouts (the default setting)  OR slow motion turnouts. Only one type of turnout motor can be used on any particular DS64.Note: Multiple turnout machines can be operated on a single DS64 output.For example, you can run 2 Peco or Atlas Snap Switches on a single DS64 output. Up to 4 Kato ...

DCS240 FAQ   I’m getting a “StealZap” or message on my DT402 rev 2 throttle. What is this? This is a feature that helps prevent having the same address selected on multiple throttles and creating unexpected operations.  When you steal you are truly stealing control of the locomotive instead of sharing it as was the case before the DCS240 and DT402 R2 firmware were released. When using a DT402 R2 throttle with an Advanced Command Station featuring expanded slots, each throttle ID is associated with the Loco Addresses it has selected.  When you select a Loco that is selected on ...

What is an LnWi? The Digitrax LnWi module is a 2.4GHz IEEE 802.11 b/g/n (Wifi) Wireless Access Point type of device that logically bridges access from compatible external throttle APP(s) running on mobile tablet or smart phones onto a Digitrax LocoNet. The LnWi is an independent method for Digitrax users to control locomotives, and can be used at the same time as e.g. Digitrax Duplex or Simplex Wireless, and IR/wired throttles and other Wifi LocoNet access devices on the same system it is wired to. The design goal for the LnWi was to make it very easy for a Digitrax user ...

Application Note: Walthers/Life-Like F7 H0-Scale steps needed for the DH163D DH123D decoder installation. Remove packing protectors screwed to coupler pockets: Carefully remove shell by spreading sides at side windows: Here's an alternate method for removing the loco shell - our F7 unit had a particularly stubborn shell. In place of the X-acto knives pictured, we recommend toothpicks or something a little safer.. Remove DC Plug (or a DC Printed Circuit Board in this case) from the wiring harness: DC Plug shown removed: Plug DH123D or DH163D decoder to 9 pin wire harness and mount it as shown: Reinstall loco shell.

This procedure is best done after installation of the decoder to the turnout.  The process is "blind", so it is easier to program this decoder after installation because you can then test the operation of the turnout with its new address.  The DS51K1 can be installed into the base of the turnout or attached to the bottom of the layout near the turnout.1. Turn off track power and temporarily connect the yellow programming wire from the DS51K1 to the same rail as the black wire.2. Turn on track power.3. Using your throttle, select the address you want to program into ...

I'm looking to wire Tortoise switch machines on a DS64. When the track switch is thrown I want to power 1 color light (non-LED). When the track switch is closed, power a different colored light. Is this possible using the DS64 inputs or the Tortoise connections? The DS64 does not have separate connections for indicator lights for trackside or for a control panel. However, indicator lights can still wired to work with the DS64. Tortoise or other slow motion swith machines can be wired in two different ways. If using LEDs, a two leg, bipolar LED can be connected in ...

The BDL168 can be used as an autoreversing unit for return loops. One of the BDL168 Detection Sections is connected to the non-reversing area, with the balance of the detection connections being made within the reversing area. Here is a wiring example: Note that an auto-reverse section can only use detection sections that are contained in a BDL168 zone that is correctly set up for auto-reversing.

1. Read the instructions FIRST and PLAN your installation. Have the proper tools on hand. 2. Choose a locomotive that runs well on regular DC. 3. Choose the appropriate decoder for your installation. 4. Test the decoder before installation. 5. Carefully disassemble the loco. 6. Isolate the motor! 7. Follow the decoder's wiring diagram or installation instructions. 8. Test the installation first on DC then on DCC. (If the lights are flashing the first time you apply power, remove the loco from the track and locate the short circuit in your installation.) 9. Customize your decoder by programming individual CVs.

  How to Configure the DS54 for one-button turnout controlThe local buttons, throttle, or any other turnout control device connected to the LocoNet can control the DS54 output when the DS54 is connected to the rails. The following drawings indicate the general wiring schematic for a one-button control of a turnout using either a Dual Coil (upper) or slow motion (lower) switch machine. The following two charts indicate operating criteria and CV settings for one-button turnout control. 

Q: I want to use the AR1 for a reverse loop between two different power districts (i.e. different booster for each connected track). Is this possible or do I need to make a special wiring set-up to do this? SThis diagram shows how to do this The usual rules apply, the AR1 track section must be longer than the longest train you will run.

DG583S - Function Outputs 1. Function outputs are rated at 2 Amps each. Do not exceed the decoder’s 5 Amp total output rating. This total includes the motor current and total of all function output currents.2. To use a function output with an inductive(coil) type load, see the Digitrax Decoder Manual for more information to avoid damage to the decoder.3. See the Digitrax Decoder Manual for full details of wiring 12-16V lamps, 1.5V lamps, and LEDs. Lamps that draw more than 80 mA when running require a 22 ohm 1/4 watt resistor in series with the directional light function lead ...

1.  Digital technology gives extremely reliable operation and the technology is almost infinitely expandable without causing backward compatibility problems (analog systems are inherently more restrictive). 2. Digital systems make wiring simple and easy to install. 3.  Digital systems encode information sent from the command station to the decoder as numbers grouped into packets, new types of packets can be added to a digital system to send more information thus extending the existing system without causing backward compatibility problems.

I think this is a duplicate  Z  Needs to be beefed up or discarded. Command Control systems, both analog and digital, allow you to simulate prototypical train operation on your model railroad. With Digital Command Control you can operate multiple locomotives independently at the same time on the same section of track without a computer and without blocking or other complex wiring schemes. Digital Command Control systems use digital data packets to communicate commands to decoders that control locomotives and turnouts on the railroad.

Command Control systems, both analog and digital, allow you to simulate prototypical train operation on your model railroad. With Digital Command Control you can operate multiple locomotives independently at the same time on the same section of track without a computer and without blocking or other complex wiring schemes. Digital Command Control systems use digital data packets to communicate commands to decoders that control locomotives and turnouts on the railroad.

You can easily control sound units like the Keller SU1990 by using the function leads on Digitrax Decoders and DCC command station that can control decoder functions. These instructions for connecting a Keller Engineering Diesel Sound unit to Digitrax DH83FX & DH140 series decoders was writtne many years ago.  Any modern Digitrax decoder with 4 function leads can be used. Equipment Needed:1) A Digitrax Throttle, Booster/Command Station or other DCC command station capable of controlling decoder function outputs.2) Any Digitrax decoder with at least 4 function leads will work here.3) The locomotive you wish to convert, be sure to check the ...

Is it possible to add a pair of PM42 Power Management Modules between the command station Rail A/Rail B outputs and run the resulting output from the PM42's on as many as 8 sets of Rail A/Rail B Wires to 8 isolated power Zones? These isolated power zones could have their Common Zone (Rail A) Wires running through RX1 transponding receivers connected to an RX4 ribbon cable running to the BDL168 for the purpose of interfacing with the SurroundTraxx Multi-Train Sound System. If this is possible, it would only require 5-6 of the DS lines on the BDL168 to be ...

What is it and how do I find a DPDT?It's an electrical switch; double pole - double throw (DPDT). Here is a schematic of a DPDT: More typically, they look like this: The DPDT is very common to model railroading and found at just about any store that sells electronics.  It comes in a variety of arrangements, with the most common being a DPDT Center-Off switch.  Analog OperationsIn the early days of Direct Current model railroading, reverse loops had to be controlled by hand, and the DPDT was perfect for the job.  The DPDT was wired in such a way ...

You can have the power and reliability of Digitrax boosters even if you use a Lenz Command Station. You can use Digitrax boosters to automate reverse loops, too. Digitrax boosters can be used with the Lenz Command Station to provide more power for driving the layout. Many customers are using DB150, DB200, or DB100 series boosters instead of LV100's because the DB150’s & DB100's are very reliable 5 amp boosters with plenty of heat sinking capability to prevent heat related booster shutdows. Equipment needed: 1) A Lenz LZ100 Command Station. 2) A DB150, DB100 or a DB200 series booster. 3) ...

The BDL168 is designed to be used with power management devices such as PM42. The BDL168 is designed to operate “downstream” of the Digitrax boosters and power management devices. The BDL168 is the "last" device in the chain from booster to power manager to BDL168. It is connected directly to the track detection section. There should be no other connections to any detection section that will draw track power or the detection section will always show occupied. If a device is used to switch off power feeding the BDL168 and the track it is connected to, for example, a PM42 ...

  Q: How can I configure the DS54 for block occupancy detection? A:  Any DS54 input can serve as a block occupancy message generator. All that is necessary is to activate a DS54 input with a device that can detect the presence of a train within a specific area/location. The DS54 input can respond to a number of different block occupancy devices including the BD1, BD4, and isolated contacts. The following drawings indicate two different methods (wiring schematics) for the connection of devices to the DS54. The upper drawing Is for isolated contacts and the lower drawing is for BD1 ...

Many thanks to Dick Sutcliffe, Superintendent BR &T Railway Co. for this application note!Install the DN121 in the tender   1. The tender is easy to open by removing two screws so you can pull the decoder out and put in a plug when running on DC layouts.   2. Use a piece of styrene to raise the decoder off the weight.   3. Notch the front edge of the tender frame to bring the wires through to loco (all power pick up is in the loco).   4. Split the loco frame to isolate the motor brushes, remove the contact springs in the ...

My question is: How do I mount the PM42? Do I need a special housing in order to mount it under table? It appears to me that mounting it flush against a surface would prevent, or make it extremely difficult, to attach the 44-pin connector. Digitrax manufactures three devices which have a 44-pin connector. These are the BDL168 (and its predecessor the BDL16), the SE8C and the PM42 (and its predecessor, the PM4). These best approach to mounting these devices is to screw the connector directly to the wiring panel board. Drill mounting holes in the end of the 44-pin ...

I would like to use a Tomar Searchlight Signal such as model # 858. It has three color LED for each head. The SE8C manual shows the wiring example for bi-color LED signals. Is the SE8C able to control the three color LED signals as well? The bi-pole LED's can be used to produce a yellow "Approach" indication. The SE8C sends an AC signal to the LED, alternately lighting both the red and green sides to make a yellow (or "amber") Indication. Please see below: "A2" is connected to produce an approach (yellow) indication. You may find that the yellow ...

Basic tools for soldering: a soldering iron, solder, wire cutters, wire strippers, tweezers, heat sinks, etc. This photo does not show an example of desoldering braid which is useful for touch ups and removing mistakes. If you are building a model railroad, you will need to learn to solder. This skill is used for attaching track feeds to the rails to provide power to the layout, for installing decoders in locomotives, for building locomotives and signals and much more. Manufacturers minimize the need to solder where ever possible by using screw connectors, board repalcement decoders and plugs for installing decoders. ...

This article courtesy of Ross Webster, which dates from an earlier era before Bachmann made accommodations for DCC installs:There may be others ways do to this conversion, but this is the way I found using the Digitrax DG380 (any DG wired decoder can be used for this installation) DUE TO SOME OF THE FRAGILE ITEMS ON THE SHAY I WORKED ON A FOAM PAD SO THERE WAS NO DAMAGE TO ANY OF THE SMALL PARTS.I first tested the electrical items and made the following determinations.Free running for the two trucks was .8 amps, total. Stall, was 4.6 amps total for both trucks. Smoke ...

Keep Alive Power Jack (For DT200 & BT2) When the layout is powered down we recommend that you change the DT200 that is running as the Command Station to Advanced Throttle mode so it can power down and conserve its battery. Do this by pressing Run/Stop & Left Arrow keys together. All other Advanced Throttles on LocoNet will power down and show "idLE" when the LocoNet bus wires (pins 3 and 4 of the RJ12 plug) fall below +5Volts for more than 1/4 of a second. If the RailSync lines on LocoNet (pins 1 and 6 of the RJ12 plug) ...

Here at the Tech Support Depot, it has been our goal to improve operators' understanding of the Digitrax system of model railroad command control. We often see thoughtful words from others who are not employed by Digitrax that still have an in-depth understanding of the product line. Here, Doug Stuard talks about the UR91; these words originally appeared on the Yahoo Groups Digitrax discussion list, and are used here with his kind permission. UR91 and Throttle Antenna The UR91 antenna is the pair of 3" wires that sprout from the PC board that are arranged in a "V" similar to ...

Case Study - Texas & Southwestern The Texas & Southwestern is a small N-Scale model railroad that features a Zephyr. Here are a variety of short articles which detail the various facets of the construction and operation of this railroad. Background-Part 2 The idea behind the railroad. The Railroad-Part 3 Planning the railroad Track Plan- Part 4 Powering the Railroad-Part 5 Zephyr makes things easy. Wiring the Railroad-Part 6 Hooking things up for reliable operation. Reverse Loop-Part 7 AR1 makes things easy, but a little change in thinking is sometimes necessary. Programming Track- Part 8 A convenient feature. Zephyr Heat Problem- ...

Q: I have a late 70's or early 80's Athearn EMD DD40. An article on Wiring For DCC suggested a DH83FX - 2amp decoder for Athearn "Covered Wagons." The pictures look like the inside of my loco except the DD40 has twin motors with joined drive shafts. In researching your site, I realize that the DH83FX is no longer manufactured, but I was led to the DH163AT as the current replacement. Will this work? I have some other Athearn SD40 units, same vintage, but single motors. Is this the correct decoder for them? A: The "AT" in the decoder name ...

The TSMK, Terminal Strip Mounting Kit, includes 2 terminal strip boards with resistors for easy installation. The Digitrax Terminal Strip Mounting Kit makes it simple to connect any scale or model signal to the Digitrax signaling system without soldering. Simply connect the wires from the signal to the TSMK’s screw terminals and plug it in to the SE8C’s Signal Driver Cable. Using the Terminal Strip circuit boards You can attach any of a variety of types of model signal masts in any scale you choose to the Terminal Strip Mounting Kit. The Terminal Strip Mounting Kit has 10 screw terminals ...

The NET indicator is a red LED that displays information about what the DCS100 sees on LocoNet. When your layout is wired correctly and LocoNet is operating properly, the NET indicator will be on and it will flicker off any time a good LocoNet message is detected by the DCS100. The table below explains the patterns you will see for this indicator.

The PM42 was specifically designed to work with Digitrax Direct Home wired layouts. Any system that is configured this way will work with the PM42 with no interoperability issues. For example, CVP uses interoperable booster connections.The PM42 can be used with a DC system if it is hooked up in the negative ground return path, or even a Marklin AC digital (trinary) booster. It is possible for the PM42 to be used with most DCC systems. Digitrax has no control or knowledge of each specific non-Digitrax system and how it may interact with the PM42.

How can I connect my PR3 programming output to an existing programming track on my layout that is already set up for programming and mainline operations? Install a non shorting multi position rotary switch between a isolated section of track, 4-6” longer than your longest engine, and the various desired outputs from command stations and the PR3 output terminals. The following schematic allows a single section of track to be fed by the rail output of a command station, the programming track output of a command station, and the programming output of a PR3. To add other third party decoder ...

IPLING From time to time the latest DT602 family throttle firmware will be updated and will be posted on the product support page.  These updates may slightly modify the DT602's operation, based on customer feedback/requests and priority support issues discovered. If you are happy with the operation of your DT602, and have no issues or new features you may want, it is not required to perform an available update. All DT602 family throttles should only be firmware updated or IPL'd while plugged directly into a working LocoNet. The Digitrax provided DMF file for field updating DT602's can be used for IPL of any ...

Before sending your Digitrax mobile decoder in for repair try these troubleshooting steps to see if you can “bring it back from the dead” and save a trip to the shop and possible repair charge. As with troubleshooting anything, begin checking what could be wrong methodically. Write down your observations as you work through the list to solve the problem.The most common "repair" problem we see in our repair department is decoders that are programmed incorrectly.Many decoders we receive for repair have been programmed with CV values that cause them to seem to have a problem. The good news-bad news ...

The BDL168 manual states that 2 RX4's can be connected but it only shows how to connect one of them on Aux 2. How is the second RX4 connected? The RX4 is a 4 Zone Transponding Receiver Add-on for BDL16 series occupancy detectors. Each RX4 is made up of 4 RX1 sensors, a ribbon cable and a connector that lets you plug the unit into a BDL16-series detector. The earlier BDL16 and BDL162 occupancy detectors had the capacity for hosting one RX4. BDL16 & BDL162 boards are labeled with AUX1 & AUX2. Only the AUX2 connection should be used for ...

Q: I am setting up a yard control panel with a CML Electronics DTM30. For the DTM30 to know what state a turnout is in, it can issue an interrogate command but my DS54's do not seem to respond with this information. Is there a trick to this? A:  According to CML: The DTM30 makes use of the “Interrogate” feature that all modern Digitrax systems use. After power up, the Command station normally sends out 8 switch commands. All accessory devices respond to these, and send LocoNet messages back reporting sensor states and point states. The DTM30 can also send ...

Prior to Disassembly Test the Decoder All Digitrax decoders are tested for proper operation before they leave the factory, but sometimes strange things happen. Therefore to insure your decoder is covered under our warranty policy, please give it a thorough test BEFORE you cut the wires. Test Run the Locomotive Be sure it runs correctly in both directions with no unusual noises or binding in the motor-gear train. If it checks out OK, then: Get Ready Before you start, get your tools and supplies together for this project. You will need the following items: DECODER TESTER - Such as the ...

Power Management is a concern on every layout.  With Digital Command Control, the main concern is that enough power is supplied to evey track section on the layout so that the digital signal is transmitted to the decoders in the locomotives and turnouts.Each locomotive uses power from the track, some for the motor, some for headlights and other functions and some for the command control electronics in each locomotive.  More electrical power is necessary to run more locomotives on the layout.  Digitrax boosters provide between 2.5 amps & 8.0 amps.  A small N Scale or HO Scale layout with two to ...

Q:  I recently split my layout in half, with a DB150 acting as a booster powering one side and a DCS100 powering the other. I'm trying to reconnect the bus feeders to the rails, which all worked properly before the split. Now when I reconnect the feeders there is no short indication, BUT when a loco goes over the insulated gap between the two sections, a short occurs. A:  This is a common issue when the first booster is added to a DCS100/DCS200 command station. MOST DCS100/DCS200 command stations come from the factory set with Rail A & Rail B connections that are the opposite ...

Transponding gives you operations mode readback of decoder CVs while they are on the layout (for decoders with this feature). Your dispatcher will know where trains and other equipment are located. Feedback from your transponding decoders lets you know the zone location and address of any piece of transponding rolling stock on the layout. This information can be presented on a display panel, your computer or even on your throttle. Feedback from the locomotive decoder also can provide information about the speed and other status data for the specific locomotive. With transponding, you can FIND the location of a specific ...

  Q:  Can I use a PM42 with a non-Digitrax DCC Command system? A:  The PM42 was specifically designed to work with Digitrax Direct Home wired layouts. Any system that is configured this way will probably work with the PM42 with no interoperability issues. Digitrax has no control over or knowledge of each specific non-Digitrax system and how it may interact with the PM42. The PM42 can be used as a stand-alone auto-reversing unit and short circuit manager with many third party DCC systems, but for systems without LocoNet capability a number of the networked management features will not be available. ...

1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the light board, so that you can install the new decoder in the same orientation. 2. Carefully remove the factory light board by sliding it toward the back of the locomotive and out from under the frame clips. Then gently lift the board out of the frame. Be careful not to bend the motor contacts. Apply a small piece of Kapton tape to saddle area of the frame above motor. 3. Install the DN163K2 decoder by angeling it slightly as you insert the front corners into the forward ...

Operations mode (OPs mode) programming allows you to program decoders on the layout instead of having to move them to a separate programming track.  This is a write only programming method.  If you want to be able to read back the values written to a particular decoder using Ops Mode programming, you will need to install transponding on the layout.  If transponding is not active on the layout, you must use an isolated programming track for reading back CV values.The extent of the area with OPs Mode readback available depends on how muchof the layout is instrumented for transponding. The ...

Q:  Can two sections of a single PM42 be configured to perform both the task of a circuit breaker and also automatic reverse section control for a single reverse loop? The PM42 can be configured so that one section of the PM42 is used for circuit breaker operation, feeding into another section of the same PM42 which is configured for automatic reverse section control. In the field, this configuration has been found to be unreliable in some layout configurations.  If you are having problems getting this to work in your setting, we recommend using an AR1 to handle the automatic reversing secion.  The ...

Troubleshooting Your Installation To get the best performance out of your duplex radio installation, walk around the layout and check Duplex operation to ensure complete signal coverage. Depending on the layout size and geometry and surrounding materials it is often possible to move the UR92(s) to better cover dead-spots. Experimenting with UR92 location usually will quickly provide a position that is best for most layouts. Note that DT402D orientation and your body position may also affect range and reception. On very large layouts or layouts with problem areas, it is possible to add more than one UR92. Adding extra units ...

The Series7 Stationary (or Accessory) decoders are configured to not use, or need a CV Service Mode (SM) programming track. It is impractical to disconnect these fixed wired devices from a layout to configure on a SM track, unlike a mobile locomotive decoder. Series7 devices are configured when operating on a working LocoNet system to access all product capabilities. As detailed in the product Instruction Sheet (IS), the units have a number of Option Switches (OPSW's) that may be modified by; pressing the OPSW button and sending the appropriate SW# as Thrown or Closed. The IDSW button allows the setting ...

Note: This page applies only to Challenger SetsOur customers continue to come up with different combinations & configurations to suit their individual needs so, feel free to customize your own CTX/CTY!Some users choose to hard wire 4 throttles for the 4 different channels so that the throttles are not able to change locomotives within the group.Parts List:Radio Shack Part NumbersSW-1: 6 Position Rotary Selector Switch, # 275-1386, CTX 1, CTY 1C1-C4: 0.047uf Disc Ceramic Capacitors 50v, # 272-134, CTX 2, CTY 2D1-D5: 1N4148/1N914 Small Signal Diodes 50v/100ma, # 276-1620, CTX 1, CTY 2SW-2/SW-6: Normally Open Push Button Switch, # 275-1566, ...

Simplex Radio Coverage One UR91 should provide full coverage for a typical model railroad under most circumstances. Simplex Radio reception is affected by metal objects between the throttle and UR91 simplex receiver, or large metal objects adjacent to the receiver; a furnace is one example of such an object. Such objects cause a second reflected signal, impairing the radio throttle signal's ability to reach the UR91. In this case, the receiver gets the signal directly from the throttle, then another signal right on top of it from the reflection. Moving the UR91 to another location may solve this problem, or you ...

The UR92 is simple to install and begin using in your new or current layout. 1. In most cases a UR92 should be situated near the physical center of a layout and will typically cover a circle of about 300+ feet (~100 meters) across, which will be adequate for most layouts. Some layouts may require additional UR92s for adequate signal coverage. 2. Connect the PS14 DC power supply to UR92 via the DC power jack on the side. The green and red LEDs should blink and then the red LED should stay on. 3. Connect the UR92 to your working LocoNet ...

CTX/CTY throttles allow you to have up to 4 separate throttles controlled by 4 different operators rather than 4 throttles controlled by one operator as in the CT4 that comes with your Challenger Set. Digitrax provides these instructions so that you can build your own throttles to your own specifications. You are free to choose any knobs, buttons & cases you like, the ones on the parts list below are just suggestions. These throttles give you the option of expanding your operations cost effectively. The CTX throttle controls speed & direction for one train in the operating group & can ...

Zephyr Rear Panel Connections1. RAIL A & B - for connecting the DCS50 to the rails on the layout.2. PROG A & B - for hooking up the programming track. Section 16.1.3. JUMP 1 & 2 - for connecting one or two smooth DC power packs to the systemfor use as additional throttles. Section 25.24. POWER IN - plug in the PS315 here.5. LOCONET PORTS A & B - for connecting the DCS50 to other LocoNetdevices for expanding your layout.6. YOUR LAYOUT -  You can connect Zephyr to most existing layouts.

The ability of a variety Digitrax throttles to work together on layout equipped with a variety of wireless technologies is part of the beauty of LocoNet.  With LocoNet, it is simple to add components to the system and have all of them work together. Digitrax infrared throttles will operate on any layout equipped with UR90 infrared receivers, UR91 simplex receivers and/or UR92 duplex transceivers.  All of these panels are equipped with infrared receivers.  All current model Digitrax throttles have infrared emitters that will work wirelessly with any panel that has an infrared receiver.  All current Digitrax throttles can also be used ...

What about using a Digitrax-decoder-equipped locomotive on a layout having only DC power?It is possible, but analog operation of DCC equipped locomotives is becoming a bit of a rarity. In earlier times some locomotives were delivered from the manufacturer with a DCC decoder in place and a jumper plug was used to select the operating environment. Digitrax still offers a jumper plug for use in some configurations; you remove the decoder and replace it with the DHDP or DNDP. With later generations of decoders, it is possible to operate on a DC layout with the decoder in place. To quote ...

  Digitrax Duplex Wireless Functional diagnosis and debug process:   Duplex Background:  The Digitrax Duplex radio system is a two-way RF radio link connecting wireless throttles (DT402D & UT4D) via a UR92 onto LocoNet.  It operates on one of 16 user-selected channels in the 2.4GHz Wi-Fi frequency band.  FCC rules requires that all WI FI devices including the RF24 Duplex transceivers (part of Digitrax Duplex throttles and the UR92) operate co-cooperatively in this 2.4GHz band and have to accept whatever wirelessenvironment is present.  This means that there is no guarantee that Digitrax Duplex will work in all situations or that it will ...

DCS50 Zephyr - Quick Start Guide 1. Unpacking Your ZephyrUnpack your box and locate the DCS50 Command Station and the PS315 power supply. 2. Before You BeginBefore proceeding to the next step, make sure the Throttle Knob is turned all the way to “STOP” and the Direction/ Brake lever is set to “BRAKE”. 3. Connecting the Pieces TogetherOn the back of the DCS50, locate the gray screw terminal strip. On this strip, locate the two terminals labeled “RAIL A” and “RAIL B”. Attach your layout track wires to these terminals. It does not matter which is which. 4. Turn on ...

The Texas & Southwestern has a reversing loop, and DCC insures reliable and simple operation of trains in the reverse loop. This reverse loop is handled with a Digitrax AR1 Auto Reversing Controller. The automated features of the AR-1 make for seamless train movements, but an issue quickly arose. Because a reverse loop in a traditional DC-powered model railroad environment required manual operation, the track insulating gaps for the loop were usually located for the convenience of the operators. So the track gaps of the original track plan were situated to keep this inconvenience to a minimum. Note also all ...

Proven technology for bi-directional layout control without the need for modifications to your existing DCC system investment. Know the detection section and/or zone location and identification of any specific locomotive or other rolling stock equipped with a transponding device. Yes, now your dispatcher will be able to know "who you are and where you are"! Location and identification information are updated constantly on LocoNet and can be displayed on a track diagram. Adds operations mode readback of CVs to your layout. Data received by the system from mobile decoders can be used for display, automation, sound processing and much more. ...

Q: I am building a new DCC layout that will include a logging spur that is simply a single long piece of track with no loop. I want to have a train go back and forth on this track which automatically reverses when it gets to each end. While the AR1 was designed for reversing loops, can it be wired to simply reverse a train on a straight piece of track? A:  Not in the way that you intend. One of the interesting problems with DCC is that we often still think in terms of DC, where the track polarity ...

DT400R is a radio equipped throttle. To use your DT400R as a radio throttle, you will need to install a radio receiver on your layout. All DT400s are “InfraReady.” This means that your DT400 comes with IR LEDs that will send infrared signals to the layout. To use this InfraReady capability, you just need to install one or more infrared receivers on your layout. A 9 volt battery must be used to power the DT400/R for tetherless operation. Using DT400/R as a tetherless throttle is easy: 1. For Infrared operation, plug in at least one Digitrax IR receiver (UR90 or ...

The DCS50 Zephyr displays three types of error messages: Short circuit shutdown occurs when the DCS50 detects a short circuit in the power district where it is connected to the layout. This can be a loco that has derailed or picked a switch or some other conductive material lying across the tracks. In this case you will see “o”s walking across the display from left to right. Once the short is cleared, the DCS50 will resume normal operations. Current overload occurs when the DCS50 has reached its 2.5 Amp current limit. In this case you should run fewer locomotives or ...

On layouts set up for Digitrax transponding with transponders in locos and rolling stock and transponder receivers installed on the layout, the DT40x’s FIND Key is used to turn on the find command. The FIND function lets you see the zone location of transponders on the layout in your throttle display. To use the FIND Command: 1. The layout must have Digitrax transponder receivers (BDL16x & RX4s) installed and configured. 2. The loco or other rolling stock that you want to track must have a transponder installed.  This can be either a transponding decoder or a stand alone transponder. 3. ...

The UT4 comes InfraReady for layouts that are equipped with one or more UR90 infrared receivers. For Infrared operation:1. Install one or more UR90 infrared receivers on your layout.  These should be connected to LocoNet and powered.  If you have UR92s and/or UR91s present on the layout, these also support infrared operation.  You will need enough infrared receivers installed on the layout so that the throttles you use can "see" the receivers since the transmission is line of sight.  You may also encounter problems in rooms where there are large windows that would interfere with the transmission.2. Install a 9 ...

  I have a 14x24 foot room with a shelf layout on two levels. 1st level is about 24 inches with two main lines and some industries, a moderate freight yard, moderate intermodal facility and passenger station. The second level is 18 inches and will contain one and two main lines with mostly industries. This would qualify as a "medium to large" model railroad. I would like to have 1-5 operators with 2-10 trains running at one time as permitting. At least four Universal Panels would give all operators full access to LocoNet as necessary. At least one UP each ...

DS64 is set up by setting Option Switches (OpSw)This is how to set option switches on the DS64:1. Begin with your DS64 powered up. Turnouts can be either connected or not.2. On the DS64 press and hold the OPS button down for about 3 seconds until the red OPS LED and green ID LED begin to blink alternately. This indicates that the DS64 is ready to change the option switches.3. Using your DCC throttle, select the Switch Address that corresponds to the OpSw number and send the Closed or Thrown command corresponding to the setting you have chosen. Refer to ...

We recommend testing your new SE8C prior to installation on your layout. The following testing procedures will help familiarize you with the general operation of the SE8C. Track power needs to be ON, a working LocoNet connection and a throttle or PC running DCC control software. Pre-Installation Set-Up 1. Solder one wire from a 12V AC or 15V DC power supply to Pin 3 and the second wire from the power supply to the Pin C on the 44-Pin edge connector; this powers the SE8C. Digitrax manufactures the PS14, which is appropriate for this installation. Multiple SE8Cs can be powered ...

Q:  I am looking for a wrist or neck strap for a UT4R/UT4D to prevent dropping unit. Can you help with a source? A:  It is really hard on the throttles when you drop them on the floor.Here's a handy tip from Zana: Take the throttle cord and loop it with a rubber band and hang it from a Digitrax show lanyard (any other lanyard will do in a pinch).   You can also install hooks on the fascia of your layout for holding throttles with looped cords.I have also seen customers glue things to the back of the throttle for ...

Under what conditions can the PR3 be used as a Stand Alone LocoNet Terminator? The PR3 is so designed so that it can be configured to act as a stand alone LocoNet controller in the event that a Digitrax command station is unavailable for the control of a series of LocoNet compatible devices. There are two major situations that would require the PR3 to act as a stand alone LocoNet controller. The first situation is where one of the many advanced features offered by the LocoNet and the various LocoNet compatible devices is desired to be used on a layout ...

Regulated power supply delivers more power with less heat for more efficient booster operation. Operates up to 4 Five amp boosters. Scale selectable for use with N, HO or large scale. DC Ammeter. On/Off Switch. Integral cooling fan. Design coordinated for use with Digitrax products. One "Y" Cable (P/N YC52) Included for convenience with dual 5 amp protected outputs All secondary devices must be properly fused on their power input leads for their rated capacity. For example if you intend to use the PS2012 to drive a 5 and an 8 amp booster, you must input fuse these devices for ...

  Connecting BD4 to an SE8C?The BD4 is a block occupancy detection device designed as an add-on device that can take advantage of the LocoNet hosting capability of the SE8c signal decoder.   It is connected this way: The installation of a BD4 is relatively simple. Looking at the BD4, you will find a 5-point terminal block on one end and two (LED1 and DS1) 10-pin (5x2) headers on the other. There are three termination areas: a) The 5-point terminal block (left) is for the interconnection between the rail power source and the rails. b) The LED1 10-pin header is ...

There was a time when every mobile decoder installation was a custom installation. In those early days, we were just feeling our way along, trying to find ways to make the existing supply of decoders fit into locomotives which had been designed in a different era. Fortunately, things have changed along the way, and in many cases, the Digitrax Decoder Selection Guide will list your locomotive. But many locomotives are not listed because they are too new or are too generic for a special listing. So, from time to time, you will have to "wing it" just a bit to ...

The layout uses twenty-eight turnouts on the mainline and an additional eleven turnouts in the yard. Each turnout is powered by a Tortoise slow motion turnout motor. Each of the twenty-eight mainline turnouts has three dwarf signals associated with it. The aspects of the signals are shown below. The indications of the signals are: Green = Proceed Yellow = Proceed with caution Red = Stop Each signal has one head with two LEDs. There are also thirty-eight mainline block signals (red/green) that are controlled by heavy duty single pole double throw relays. This makes a total of 122 signals. Since ...

While it is possible to use RJ12 telco jacks as throttle jacks on LocoNet, the UP5 is much simpler to use and looks much more professional on the front of the layout. The UP5 is shipped as a kit that must be assembled.  You will need to attach the front panel to the circuit board using the screws provided as shown below before installing the entire unit on your layout.  If your front panel does not fit at a "perfect" 90 degree angle to the circuit board, this is will not affect the functionality of the unit.Make sure to line up the Track ...

  Can I add Radio and IR to my Zephyr Xtra?Yes.Adding radio and/or IR to Zephyr and Zephyr Xtra is the same as adding it to any other existing Digitrax layout or Digitrax Starter Set. Digitrax offers InfraRed, Duplex Radio and Simplex Radio systems for wireless operation.  Any combination of these wireless methods can be used on the same layout at the same time.Infra Red Wireless OperationAll current Digitrax throttles are Infrared capable (InfraReady) in that they come from the factory equipped with the IR emitters required to send IR information to LocoNet.  To use this functionality, you only need to ...

Q:  Where do I locate UR90 for best performance? A:  Infrared signals are transmitted and received in the line of sight between the transmitter and the receiver.  Most problems with IR reception are caused by people or things blocking this line of sight.  UR90 should not be mounted in the layout fascia below track level because that is where we stand when we run trains.UR90 works best when mounted on a wall, opposite the operators, near the ceiling, at a 30° to 45° downward angle. The reason for this positioning is simple. When you are making speed and function changes on ...

Can I add Radio and IR to my Big Boy?Yes.Adding radio and/or IR to Big Boy is the same as adding it to any other existing Digitrax layout or Digitrax Starter Set. Digitrax offers InfraRed, Duplex Radio and Simplex Radio systems for wireless operation. Any combination of these wireless methods can be used on the same layout at the same time.Infra Red Wireless OperationAll current Digitrax throttles are Infrared capable (InfraReady) in that they come from the factory equipped with the IR emitters required to send IR information to LocoNet. To use this functionality, you only need to add one ...

Security ElementsThe Digitrax Signaling System is organized around the concept of what we call "security elements", which are similar to what U.S. prototype railroads call "plants" or "interlockings". The Digitrax SE8C signal decoder displays aspects for up to 32 heads for 8 individual security elements (plants) using either a LocoNet Throttle or a computer with compatible software. When used with associated occupancy detectors and compatible software, the SE8C can be set up to protect the turnout with signals as shown by the example below. Note that trains can move from A to B, A to C, B to A or ...

An important series of developments in model railroading have taken place that makes it much easier to enter the hobby and enjoy it right away.  DCC is part of that process since it makes it easier to handle the train operation aspects of the hobby.  Other improvements have been the ready availability of correctly decorated locomotives and cars, scenery systems such, and, most importantly of all, advanced track systems.  Where it once required hours to get your model railroad’s track in proper operating form, the new modular track systems have greatly simplified things.  Everything just clicks together.These modular track systems ...

Digitrax decoders have outputs that can control lamps and other on/off devices installed in your locomotive.  These are called functions.  Functions are things like: lamps, sound units, smoke units, etc. All Digitrax decoders are equipped with two or more function outputs that are used to turn functions on and off.Decoder function outputs can be:1.   Leads (wires) attached to the decoder that are used to hook up external functions.  See Table I below for wire color codes used on Digitrax decoders.or2.   Pre-wired function outputs that hook up by just plugging in the decoder. This is the case for decoders that ...

Follow these simple instructions to determine the best location/s on your layout for installing your UR panels for the best possible infrared or radio reception. With LocoNet, you can use Infrared, Duplex Radio and Simplex radio individually or in any combination on your layout.You'll need to be able to observe whether your command station is receiving commands from the UR panels when you are installing infrared or radio receivers and transceivers.  Your Digitrax command station makes it easy to determine when the system is receiving a signal and when it is not.  You can observe the NET LED and the Track Status Indicator or your ...

Your Super Empire Builder Starter Set contains: The DB150, which is the system’s DCC command station. It generates the DCC signals that control decoders and other devices on your layout. The DB150 is also a DCC booster. Boosters receive DCC signals from the command station, amplify them and put them on the track along with the power from the transformer to run the locomotives. You can have several boosters on your layout to provide additional power to run more locos. Depending upon the set, there is either a DT402 or DT402D (duplex radio throttle), which is the DCC throttle that ...

  CV29 is assigned a single value which chooses a combination of specific effects: 1. Speed step control. 2. Speed table On or Off. 3. Analog mode conversion On or Off. 4. Normal Direction of Travel (NDOT). 5. 2 digit addressing or 4 digit addressing. Analog Mode Analog mode conversion is very convenient if you plan to run your Digitrax decoded locomotive on regular DC layouts. With analog mode conversion enabled, the decoder will automatically begin operating as a DC locomotive when no DCC signal is detected by the decoder. This means that if you place your Digitrax decoder equipped ...

1. Before using your TL1, set its address. This may or may not be the same address as a mobile decoder already installed in the loco or car depending on how you are planning to use the TL1. In the case of TL1s being used as a stand alone transponder or as a function decoder, choose an address that is not associated with another mobile decoder address in use on the layout.2. Connect the RED & BLACK wires of the TL1 to a service mode DCC programmer and program the TL1's address as you would any mobile decoder address.Follow the ...

If you want to change the address or other settings of your locomotive decoders, you must set up a programming track. It is very important that the rest of your railroad can be isolated from the DB150 and the programming track when you are programming a locomotive. Decoders are programmed when the DB150 command station sends programming information to them through the rails. There are two basic ways of programming decoders. Service mode programming broadcasts a message to all DCC equipped locos that are on the track. Because this is a broadcast method, you will need to set up a ...

Based upon a layout designed by the late, great John Armstrong which appears in the classic book, 101 Trackplans for Model Railroads [Kalmbach Publishing, 400-12012, still in print], this railroad combines different elements to offer varied model railroad operations. At the center right of the railroad is the Union Passenger Station. From this station, trains can operate out & back, which is to say that a passenger train leaves the station, goes out onto the circular main line and eventually comes back into the station after passing through the reverse loop. Another passenger train can operate point to point, meaning ...

Program the TF4's Address & Function Outputs1. Before using your TF4, set its address. This may or may not be the same address as a mobile decoder already installed in the loco or car depending on how you are planning to use the TF4. In the case of TF4's being used as a stand alone transponder or as a function decoder, choose an address that is not the same as another mobile decoder address in use on the layout.2. Connect the RED & BLACK wires of the TF4 to a service mode DCC programmer and program the TF4's address as ...

Can a UR91 be returned and upgraded to a UR92? No. Our recommendation is that when upgrading to the DT402 throttle, the layout owner purchase a new UR92, but keep the UR91 installed for those who still have the simplex radio throttles. That way anybody can run on the layout.

If the layout starts to “get away” on you, either PRESS the PWR Key followed by the N- Key or, turn the track power to “SLEEP” on the command station. Either way, the layout will stop to give you a chance to regain your composure. To resume operations where you left off, press the PWR Key followed by the Y+ Key

  One major consideration is that the reverse section controlled by the AR1 must be longer than the longest train. It is a common misconception that the AR1 will work with an analog controlled ("DC") locomotive; it will not. The AR1 is meant to be used only in a DCC enviroment. The AR1 coordinates the phasing of the reversing section with that of the mainline (non-reversing) section of the layout.  Because a Digitrax layout can be a complex enviroment with detection and transponding, etc. consult the approriate Digitrax user manuals and the Digitrax Tech Support Depot knowledge base.  

The FIND Key is used in conjunction with a layout instrumented for Digitrax Transponding and locos or cars equipped with transponders to find the location of those pieces of rolling stock on the layout.

To stop everything on the layout immediately:Press the POWER key to turn off power to the whole layout. This option will stop everything on the railroad.

Q: What is a programming track? A:  A programming track is a section of track that is used to program the mobile decoders in locomotives.  Sometimes it is called the service mode track or service mode programming track.  It must be electrically isolated from the rest of your layout and connected to the Prog A and Prog B terminals of your command station.  The programming track can be completely separate from the rest of the layout or can be isolated by double gapping and using an electrical switch to allow locos to move from the programming track to the mainline before and after programming.   Usually ...

Adding UR92s will provide better signal coverage for complex layouts. If you are adding more than one UR92, be sure to connect all of the units before changing the Duplex Group name or channel number or you will have the units automatically re-negotiate these values with each addition. 1. Add the UR92(s) to your LocoNet. (See UR92 Installation articles, below.) 2. After adding extra UR92s, use the DT402D to turn OFF layout track power and then turn track power back ON. This forces all the UR92s to automatically negotiate a common and permanent single Duplex Group name and channel number. ...

The STOP key has two uses: as an emergency stop for the locos on the layout and as a shift key used in conjunction with other keys.Emergency Stop keyThe factory setting for the STOP key is for Local Emergency Stop which stops just the locos controlled by the two throttle knobs on the DT300. The STOP key can also be set for Global Emergency Stop which will stop all of the locos on the layout.  This is done by setting throttle option switches.Using the Stop key as a Shift KeyThe STOP key is also used as a shift key in ...

What is the difference between boosters and power management? A Booster is the device that provides the electrical power to the railroad. Most Digitrax command stations have a combined booster. The command station generates the DCC signal then sends it through a booster to the layout. A small model railroad may only have the command station and booster, while a large railroad will have numerous boosters. Multiple boosters provide more power to larger layouts.Additional boosters receive the DCC signal from the command station via LocoNet. Power management usually refers to the devices which act as circuit breakers and power distributors. ...

Differences in the DS74 from the DS64: Up to date and compact LocoNet design with customer IPL/firmware field update capability using DigiIPLII. All plug-in connections. Can support on expansion header up to 4 DSXCP1 fascia SW control panels with SW direction indicator LEDs. 8 internal LocoNet integrated System routes, that can be conveniently edited on a DT602 with latest IPL update. Configurable unit Base switch address when on layout. No need to remove from layout to service/configure. Automatic DS74 switch address overlap detection, and correction capability when editing with DT602. Indicates internal IPL Sub-version loaded to latest DigiIPLII rev 2.9 ...

The 5 Amp DCS100 and the 8 Amp DCS200 share the same front panel layout. There is a variety of indicators, switches and connectors: Power Input The two POWER IN terminals on all Digitrax boosters & command stations are the power input connections. Power On Indicator This green LED indicates that the power to the DCS100 is on. Ground Terminal The terminal marked ground provides electrical safety features and an RF ground reference for minimum radiated noise. This should be the ONLY point of any DCS100 installation that is connected to the AC safety ground pin provided on most 3 ...

Two Programming Methods Are Supported by Digitrax Command Stations:Service Mode Programming is done on an electrically isolated programming track. Using this mode, the command station broadcasts programming information to all decoders on the program track.  Within Service Mode programming are Paged, Direct and Physical Mode.Because these are a broadcast modes, we must isolate the decoder we want to program from the others on the layout by using a separate programming track that is connected to the command station for programming but not powered for operation of the locomotive. This mode works with all DCC decoders. This is the most commonly ...

What is the difference between Simplex and Duplex wireless operations and what are the advantages of each?The Digitrax DT400R, DT402R and UT4R throttles operate at the 916.5Mhz radio frequency.  These throttles both use the UR91 for radio communication.  The DT402D and UT4D operate at 2.4Ghz.  They require the UR92 for radio communication. The move to Duplex is meant to improve radio operations and add radio range.  Simplex (UR91) and Duplex (UR92) can operate on the same layout without any issues or interference with each otherWith duplex radio: You’ll select and run your locomotives without plugging in.   You'll dispatch locomotives ...

The Nemo Junction module has a total of seven color light signals that regulate the flow of train traffic through this interlocking plant. Controlling the Signals with SE8C The SE8C is the signal driver, sending current to the various LED's of the color light signals. Each signal is operated via switch commands from the Zephyr. The SE8C has eight Driver Sockets, identified as DRV1 - DRV8. : A Signal Driver Cable (a 10-conductor ribbon cable) is plugged into a SE8C Driver Socket to control as many as four signal heads per Driver Socket. Each signal head can display 4 lighting ...

The SE8C uses switch addresses to operate the signals, so you may need to change some factory settings to make it work in conjunction with turnouts that are already installed on your layout. Be sure that when you configure the SE8C that the switch address ranges you select to operate the signals do not conflict with other devices, like DS64s, that are already installed. We strongly recommend that you keep accurate documentation of the address ranges used to control all devices on the layout to avoid conflicts that might cause problems. Without this record it can be very difficult to ...

The answer to this question applies to all Empire Builder sets including Super Empire Builder XtraQ:  I have just purchased a Super Empire Builder set. My expectations are for it to operate an N-Scale switching layout right now with future expansion to a larger N-Scale layout. I am a little confused as to which power supply I would need at this time. I am reading about power supplies and inline fuses, all of which is a little overwhelming to me as I am getting back into the hobby. Can you recommend which power supply will be better for me as ...

Braking sections are sections of track which will cause a DCC equipped locomotive to stop automatically. The simplest way to do this is to set up a track section where the power is turned off. This has two disadvantages. First, since there is no power, the locomotive lights will be off when the train is stopped in the section. Second, the lead loco in a consist stops as soon as it hits the dead section. Other locos in the consist will push the dead loco forward. In a long consist, you could get a situation where the last loco in ...

  How do I connect the BD4 to the DS54? The BD4 is a block occupancy detection device designed as an add-on device that can take advantage of the LocoNet hosting capability of the DS54 stationary decoder. It is connected in this way: The installation of a BD4 is relatively simple. Looking at the BD4, you will find a 5-point terminal block on one end and two (LED1 and DS1) 10-pin (5x2) headers on the other. There are three termination areas: a) The 5-point terminal block (left) is for the interconnection between the rail power source and the rails. b) ...

What are the most common applications for the PR3? 1) Stand alone Sound FX programmer As a bench tool the PR3 is the first USB and second device designed by Digitrax for the programming of the SoundFX sound decoder. The PR3 does write to and read from the sound patterns of any SoundFX sound decoder. In addition the PR3 can write to and read from any CV of most current non sound mobile and function decoders found in today's market place. 2) Digitrax command station LocoNet to Computer interface As a layout control tool the PR3 is a second generation ...

The two "POWER IN" terminals on all Digitrax boosters & command stations are the power input connections. Digitrax recommends the PS514 to power the DC200 and DB150.  Set the voltage setting on the PS514 to 16.8v or 19v.  The PS2012 can also be used to power the DCS100 and DB150.  The "Y" cable provided with the PS2012 has an embedded 5 amp current protection.  The PS2012 can also be used to power the DCS200.  The "Y" cable is not suitable for use with the DCS200 since it has an 8 amp. output. When powering your layout, make sure that all polarities and ...

Characteristics Controlled by CV61:Some Digitrax Decoders use CV61 (one of the manufacturer specific configuration variables) to give you the following options:  Non-Directional Headlight Operation, Transponding Enabled or Disabled, & Split Phase Motor Drive for Märklin AC and Lionel Type motors.The look up table below shows the effects of different CV values that you can program into CV61.  CV values are shown in hex & decimal are the same in this case.TABLE 61: CV61 Values CV 61 Value Non-directional headlights Transponding Split Field Motor/AC 00 No No No 01 Yes No No 02 No Yes No 03 Yes Yes No 04 ...

The front panel of the DCS50 Zephyr has a throttle knob & direction control lever, indicator lamps & display, which give status indications and operate your railroad. Before you select and run a locomotive, take a few minutes to look at the DCS50's controls and display.1. The Throttle Knob is the large silver and black knob on the right side of the DCS50. The Throttle Knob controls locomotive speed from STOP to FULL speed. Turn it clockwise to increase speed and counter clockwise to decrease speed.2. The Direction Control Lever is the small silver lever (located on the left side of ...

You can operate reversing sections manually or automatically with Digitrax. You must double gap (completely isolate) both ends of the reversing section just like with any other layout. If you choose manual operation, use a DPDT switch or relay to handle the polarity change as the loco enters and leaves the reversing section.   If you choose to use to completely automate the reversing section, power the reverse loop with a booster and power supply and the main layout with another Command Station and power supply. The WTL12 when running as your command station will not auto-reverse.  To configure your ...

DT400 is designed to maintain a close similarity in function & feel with Digitrax DT300, DT200, & DT100 series throttles. This family resemblance makes it easy to add new throttles to your Digitrax Command Control System and be able to use them in ways similar to the existing throttles that you are already used to. DT400 can be used with any Digitrax LocoNet System or other LocoNet compatible DCC system.   User friendly Multi-line Backlit LCD with easy to read icons and messages.   Prompts in the display guide you every step of the way. To make operation easy and ...

A speed table is a list of numbers, one number for each speed step. Many operators customize their locomotives by adjusting the CV's for Vstart (02), Vmid (06) and Vmax (05) to set the throttle response characteristics for each locomotive. This is known as a three-step speed table It is also possible to create a more complex speed table, either with 14 or 28 steps that specify the exact percentage of full power sent to the motor when the throttle is set to that speed. Speed tables can be set up for 14 or 28 speed steps, but not for ...

This H0-scale railroad track plan first appeared in the Atlas Model Railroad Company's book "Six Railroads You Can Build", written by John Armstrong and illustrated by Tad Stepek. This book was first published in 1958 and has been reprinted several times. A classic bowl of spaghetti, the Transbay Interwoven has two reversing loops and a turntable. DC Control For DC operation, Atlas specified three Atlas Controllers (for the reverse loops and the turntable), two Atlas Selectors (to control eight track segments) and ten controllers for the railroad's turnouts. DCC Makes Things Simple With DCC, the wiring of this railroad is ...

When using more than one DS64 in a DCC environment, you must assign a Board ID to each additional DS64 so that each one has a unique Board ID.You will need to set the DS64's board ID if you are planning to use the DS64's 8 inputs with a computer, system throttle, or other smart device on your layout that needs to know when a turnout has been manually thrown or closed via a particular DS64.You can use the 8 inputs on the DS64 to control the operation of the 4 outputs that control your turnouts.  For example, you can ...

Resetting Factory Defaults You are unlikely to encounter a problem that will require a factory reset. One such instance may occur if you set a password for your Duplex Group name and forget what it is. Resetting to factory default condition is an easy way to correct the situation. Note: If you have more than one UR92 in your layout, you will want to disconnect all of them to do a full factory reset on each unit as follows. Once they have been reset, reconnected to your LocoNet, and allowed to renegotiate a common Group name; you can change the ...

The DT300 is “InfraReady”. The DT300R can operate tetherless on radio or “infraReady.” Both units are also provided with a cable to attach into LocoNet when required. A 9 volt battery must be used to power both the DT300 and DT300R for tetherless operation. Using DT300 as a tetherless throttle is easy:1. For Infrared operation, plug in at least one Digitrax IR receiver (UR90 or UR91) to your working LocoNet. Because infrared signals are line of sight, more than one receiver may be necessary for optimal performance in your layout room. 2. For Radio operation, plug in at least one ...

When you are finished with your session, you should shut down the DCS50 by turning off power to the system.Shutting Down DCS50 Zephyr1. Bring all locomotives on the layout to a stop by setting set the Throttle Knob for each loco to STOP. 2. Turn track power off: Press the POWER key, the DCS50's Track Status Indicator Dot will go off. The display will briefly display "Po" followed by two characters, the Po means power off, the two characters indicate which software version is installed in the unit. The display will automatically revert to showing the last loco address selected ...

Q:  Your recommendation is to have a DB150 booster at no more than 50 foot intervals. Will one booster handle all track in that 50 foot area, i.e. a passenger terminal throat with many turnouts and switches? A:  The "50 foot intervals" applies to the maximum distance which boosters can be located from each other. This is a conservative recommendation.  You should consider how much power will be consumed in a district when locating boosters around the layout. If your power district is a single track railroad stretching over hundreds of feet of linear distance, boosters should be placed at 50 ...

The track plan of the model Kelana Jaya Rail Line is shown below: Included in the model is the double track mainline with crossovers, two elevated stations with center platforms, one at-grade station with outside platforms and two underground stations, also with center platforms. The storage yard, maintenance yard and reversing loop at one end of the system and the four track stub terminal at the other end of the system are also modeled. The yard, station tracks, crossing loops and distances between stations are all scaled to hold trains no larger than three cars. The layout is designed to ...

The DigiGroupSetup utility is in a ZIP file which is provided for Digitrax customer convenience and can be downloaded from our downloads page. Read Me Text File with DigiGroupSetup This utility is provided on an as-is basis for users with a Windows based machine configured to work with this software, and the ability to perform the setup and operation tasks detailed below. Techsupport is not configured to diagnose issues related to operating system, hardware, configuration or other possible problem areas that may cause problems with running these utilities. DigiGroupSetup: This program allows convenient Duplex system setup for any UR92 on ...

RX4 / BDL168 Hookup Worksheet BDL168 #_______ Address:________ Description______________________________________________________ Aux Power:_______ Standard BDL162 Configuration Advanced Detection Section Wiring: Transponding Method________________________________   Section Pin # Named Detection Section Description ZONE A Power In 1       1 2     Power 2 3     District 3 4       4 5     In Out Alternate Zone Comments                                             ZONE B Power In 6       5 7     Power 6 8     District ...

OPS Mode Programming Soundtraxx Tsunami Sound Decoders      This article was originally written for Soundtraxx Tsunami decoders.  It will also work for other manufacturer's sound decoders.   The individual CVs that make up an address will need to be programmed individually. These CVs are AD1, CV17, CV18 and CV29. AD1 is the Primary (short address) Default 03, Acceptable Values 1-127 CV17, CV18 are the two CVs that make up the Extended (long address), Acceptable Values 128 - 9983 CV29 is for Decoder Configuration. Values are 06 for 2-digit and 38 for 4-digit addressing. There are many other values that ...

  To use the UT2 to program a decoder you must first put the UT2 in Programming Mode. To do this press and hold “RUN/STOP” and simultaneously press “PROG”. The Status LED will now turn a steady orange color indicating the UT2 is now in Programming Mode. Set the locomotive you wish to program on an isolated programming track (See Section 5.2). Make sure that the DB150 command station is not connected to any other part of the layout. If you don’t have a programming track on your layout remove any locomotive you don’t want programmed at this time. Decoders ...

You can use your DT400 series throttle with a DCS100 or DCS200 to set up routes that are triggered by operating a single turnout address to make it either c (closed) or t (thrown). Setting up and operating routes is similar to consisting locomotives because you can cause more than one unit to operate based on a single command sent to the system. We call the turnout address that other turnout addresses are “consisted” to, the TOP address. To operate a route, use Sw (Switch) mode to select the TOP turnout address in the route and move it to either closed or ...

Programming On The Mainline: Operations Mode ProgrammingOperations Mode Programming [Ops Mode] lets you program CVs in DCC locomotives equipped with Extended Packet Format decoders while they are on the mainline.  This is handy for situations where you want to make an adjustment to a specific locomotive while it is in service.  There are also situations where mobile decoders from other manufacturers can only be programmed in this manner. A typical use for Ops mode programming would be to change the acceleration rate (CV03) or the deceleration rate (CV04) of your locomotives to simulate the weight and braking capability of the ...

The Super Chief can be used to operate routes. A Route is a group of turnouts and their specified positions that will be triggered by the activation of a single "TOP" switch address to a specified position. The DCS100 Super Chief supports up to 32 routes. Each route consists of a list that contains a TOP turnout address and its position (c or t) and up to 7 other turnout addresses and their positions. Routes are stored in the DCS100's memory and can be operated by any throttle in the system that can send switch commands. Each of these 32 ...

The DZ121 was discontinued in 2002.  There were some interoperability issues with Easy DCC, MRC and Lenz.  The exchange offer is no long valid.  This article is still published for reference only.At that time, Easy DCC, Lenz and MRC users could return DZ121's to Digitrax for no charge replacements that will work on their systems. There was no reason for Digitrax, Wangrow or NCE users to replace any DZ121 decoder unless they wre having problems.The text at that time:For Easy DCC and Lenz users who are having problems: To determine whether your DZ121 should be returned, read back CV07. A ...

  What is the difference between programing on the layout using Track A and B and using a dedicated programing track using Pgm A & B. Is there a difference in voltage, packets, protocol between the two? Programming Track Broadcast programming, also called service mode programming, uses a programming track. The programming track is electrically separate from the rest of the railroad, and is connected to the "PROG A" and "PROG B" terminals of your DCS100/200 or Zephyr (Xtra) command station.One major advantage to a programming track is that many systems can read-back the Configuration Variables (CV's) that are in ...

How Many UR90 Infrared receivers will I need?One UR90 should provide complete coverage if your room is typical, with a hard surface floor and finished walls and ceiling. However, several things can cause the need for additional UR90s, such as: larger room, odd shaped room, acoustical ceiling, carpeted floors, or book shelves or other things on the walls that can interfere with the infrared signal. How many more you'll need depends on how many of these "impediments" are in your layout room. This Infrared signal should be considered to be line-of-sight, but the IR signal does reflect off of other objects, thus the concern ...

  Simple Example of a Yard Ladder with Manual Route Buttons in a hidden yard. Set DS64 OptionSwitches 11 and 15 to 'c' closed to enable route commands from local inputs. Make sure the momentary-on push buttons are wired as shown in Fig.1 above. OPSw 11 enables the local inputs to trigger the routes stored in the DS64. A1 will trigger route1, S1 will trigger route 2, and so forth. OPSw 15 prevents the local inputs from directly triggering the outputs.Option Switch Configuration Press the OPS button on the powered DS64 for about three seconds until the red led begins ...

I am putting the finishing touches on my 10 x 20 foot H0 railroad. It is a copy of the Cajon Pass, Salt Lake & Santa Fe RR by John Armstrong (#86 in the 101 Track Plans by Linn Westcott) [Kalmbach Publishing, ISBN 0-89024-512-6; still in print]. I have decided to go with DCC and my local hobby store recommended Digitrax. The layout is in my basement, I will be the only operator, the plan has 54 track switches (34 NJ International twin coils and 20 Tortoise turnout motors). Can you give me an idea as to what equipment I ...

Q:  I am not sure where to begin. Dabbled in O & HO over the years and am now starting into S but have no knowledge in DCC. My layout is drawn, Dog Bone, with an over size of approx 20' by 11'. As of now there will be 8 turnouts and perhaps a turn table will be added or more turnouts. My intent is to run maybe 3 or 4 engines max. My only purchase so far is a Showcase Western Maryland, scale, which includes DCC with sound. My next comment is HELP! I do have a 2006 Summer ...

  My layout is in N scale, with an 85 foot double track main, a 12 track storage area, small yard, and engine facility. The layout measures 10 X 14 with two helices. There are a total of 34 engines, many of which are with their trains in the storage area. All of the already made-up trains (11) have two or three engines on them, ready to be brought up via a helix to run on the railroad. Currently, the road is divided into six parallel blocks (DC); 12 blocks in all. In the future, I plan on adding a ...

How do I connect a BD4 to a DS64? The BD4 is a block occupancy detection device designed as an add-on device that can take advantage of the LocoNet hosting capability of the DS64 stationary decoder. It is connected in this way: The installation of a BD4 is relatively simple. Looking at the BD4, you will find a 5-point terminal block on one end and two (LED1 and DS1) 10-pin (5x2) headers on the other. There are three termination areas: a) The 5-point terminal block (left) is for the interconnection between the rail power source and the rails. b) The ...

If the DB200+ booster shuts down frequently: 1. Move the DB200+ so that the heat sink has a flow of cool air. 2. Place the DB200+ out of direct radiant heat like sunshine or a room heater. 3. Try direct cooling by using a small fan to blow cool air onto the heat sink. 4. Lower the track load current. 5. Reduce the input voltage from the transformer. If the DB200+ beeps 4 times and shuts down briefly and then comes back on again, it is probably being run too close to its pre-set current limit. To solve this problem, ...

If the DB150 beeps 5 times and shuts down briefly and then comes back on again. It is probably being run too close to its pre-set current limit. To solve this problem, reduce the track current load by setting up additional power districts to provide more total power for the layout. In this case excess current consumption may clip or mutilate some outgoing packets to keep the track current within acceptable limits.

The Universal Panels all have a front made of sheet aluminum with a thin graphic overlay. There are four screw holes which are used to mount the panel on the layout fascia. When installing the panels, carefully tighten the screws; if they are too tight, the screw head will grab the graphic overlay and distort it.

I used now an Bachmann EZ Command and I will turn to Digitrax because my layout grow to fast, can I use my engine (Bachmann decoder)with an Zephyr starter set.Bachmann's site says that EZ Command is a DCC system, so you can use your decoder equipped Bachmann locomotive with any DCC system, including DCS50 Zephyr.

Q: Where do I locate UR91 for best performance? A:  The UR91 works best in simplex radio mode if it is mounted in a central location on or near the ceiling. A few layout configurations may require a second UR91 for best performance.If the UR91 is also to be used in IR mode, then the recommendations for the UR90 should be followed.

Q:  Can I use Transponding with existing Digitrax decoder installations?A:  Once transponder receivers are installed on the layout, you can run any transponder equipped locomotive. All current production Digitrax decoders are transponder equipped. Older Digitrax decoders models without transponders and decoders made by manufacturers that don't support transponding can add transponding by installing a TL1 or TF4 to the locomotive.

Yes. Digitrax decoders with integrated transponding are shipped with transponding enabled but this does not affect the operation of existing layouts not outfitted for transponding.

The PWR Key is used to enter power mode for turning layout power on and off. Once you press this key, you will be prompted to use the Y+ key to turn power on or the N- Key to turn power off.  The PWR Key is also used to turn on and off the flashlight feature. The flashlight LED will be on as long as you hold down the PWR Key.

The L & R Semaphore Indicators are used when cab signaling is implemented on the layout. These semaphores offer three indications:

If the Zephyr DCS50 repeatedly shuts down briefly and then comes back on again, it is probably being run too close to its pre-set current limit of 2.5 Amps or it may be overheating due to restricted air flow to the bottom of the unit. In this case it may clip or mutilate some outgoing packets of information to keep the track current within acceptable limits.To solve this problem, reduce the track current load by running fewer locomotives or setting up additional power districts and adding more boosters to provide more power for the layout.  With more sound decoder equipped ...

If your track does not have adequate power supply to the locomotives, then the DCC signal won’t get through either. Take a quarter or screwdriver blade and go around your layout creating electrical shorts by laying the quarter/screwdriver blade across both rails every 10 feet. Your Digitrax system should shutdown when the short is present.  When the short is removed, the booster should return to normal operation. If the unit does not see a short or it does not return to normal operation after the short is removed, then you need to add more feeders.

You can add a second Zephyr to add more power and an additional throttle on the DCS50 and two additional Jump ports for using DC power packs to control DCC locomotives.  You will need to change Option Switch 02 to c (Closed) on the second (and any additional DCS50s you might choose to add to the layout as well).  The diagram below shows you how to do this.

Shielded otr Unshielded Twisted Pair like cat5/6 is not recommended for LocoNet.  This kind of cable can causes problems due to capacitive load. These issues were observed during the National N Scale Convention in Louisville, KY on a large layout using Twisted Pair cables.  The issues were resolved when the cables were replaced.

I want to sit back & watch my railroad run. Can you do that with Digitrax?The Digitrax Command Control System is designed for prototypical operation. The objective is to provide realistic operation so that the models run like the real thing. To do this you need an engineer in control of each locomotive. The starter sets are not designed for automated train control when used by themselves. To set up automated operation, you can set up the layout with detection and or transponding and use a computer to handle the automated operations.

Transponding is proprietary technology of Digitrax Inc.  Transponding works with existing DCC compatible layouts. RailCom is proprietary technology of Lenz Elecktronik. This is sometimes referred to as "bi-directional communication."  It requires modifications to existing DCC equipment for proper operation.The two methods are not compatible, they do not use the same technology.

Will I be able to use Transponding with other DCC systems?Yes. You will have to run LocoNet, instrument your layout and install TL1 or TF4 or transponding decoders in your locomotives. You can then use a computer on LocoNet to display position and ID information for transponder equipped locos. LocoNet will run independently of your existing non-LocoNet system.

Once you have instrumented your layout for transponding, you simply add transponder equipped locomotives and you are ready to go. Digitrax decoders have been shipped with transponding included since 1999.  All current production Digitrax decoders are transponder equipped. Older Digitrax decoders models without transponders and decoders made by other manufacturers can add this capability by installing a transponder such as the TL1 or TF4 to existing DCC locomotive installations.  These transponders also add functions to the loco.

To reset a non responsive MTH decoder follow these simple steps. 1. Place the locomotive on the Mainline track 2. Select address 55 3. Enter OPS mode programming 4. Select CV55 and a value of 55 5. Write to the decoder   This will reset the decoder to address 03.  Once reset, the decoder can be programmed.  MTH decoders are best programmed in OPS mode programming on the Mainline. NOTE: When programming in OPS mode, remember to select the address of the locomotive you want to program or you risk programming all the locomotives on the layout.       ...

The following picture shows the location of all extra function pads on the DN163A0, DN163A1, DN163A3 and DN163A4.  These decoders all share the same board layout.  The length is different to fit the various models.          Note: There is not a current production DN163A2.  This decoder was retired after the manufacturer made changes to the chassis and the decoder no longer fit properly.    

Digitrax 9 pin to bare wire harnesses in 5 packs

To make the DB200+ an Auto Reversing Booster follow the following steps: 1. Remove input power from the DB200+ by turning off the Input Power Supply. 2. Move the Mode Switch to the center P/R or OP position 3. Restore power to the DB200+ by turning on the Input Power Supply. Use the below diagram as a guide to configuring the DB200+ for Reverse Loops. Please note that for Auto Reverse applications the DB200+'s Mode Switch is set to the center P/R or OP position. Also note the DB200+ connections to the track- the DB200+ track connections are NOT directly ...

There are two throttles in the "300" series: The DT300 connects into LocoNet by a 7' cable. The cable allows flexibility in movement. The throttle can be disconnected to move to another point on the layout and reconnected to LocoNet without losing the acquired locomotive. The unit will also work wireless using Infrared signals when used with either a UR90 or UR91 or UR92.   The DT300R is a simplex radio control throttle with a 1' cable to connect into LocoNet. The throttle is plugged into LocoNet to select a locomotive or to program a locomotive and then can be disconnected ...

The RD2 allows Remote Sensing of 2 Detection sections.  It eliminates the need for long runs of Heavy gauge wire to the BDL168. 1. Mount the RD2 as close to the detection section as possible to keep heavy wire to a minimum. 2. Make sure both detections sections of the RD2 are connected to the same zone of the BDL168. 3. Light gauge (26AWG) wire can be used for the 3 output connections running from the RD2 back to the BDL168. The RD2 can be located up to 200' away from the BDL168. 4. Heavy gauge (18AWG) wire should be ...

Q: What's a "Bushby bit"? A: In your command station, OpSw27 can be toggled to disable normal switch commands, a.k.a. the "Bushby bit." This allows the layout operator to use an attached PC to handle switch control logic. Under normal conditions, advanced throttles can be used to operate turnouts which are controlled by LocoNet-connected stationary decoders. The factory default setting for OpSw27 is "t". Toggling OpSw27 to "c" takes this control away from the individual throttles and gives it to a controlling computer. Such an application would be a railroad with CTC control, where the train movements are directed by ...

This installation covers how to install a Digitrax decoder with wires in any Athearn HO locomotive.  Use either our DH123 (headlight functions only) or DH163 (headlights plus additional functions) for this installation.*** Note: This installation is based on installing a Digitrax wired decoder in an Athearn Dash 9-44CW. The process is similar for any Digitrax mobile decoder with wires. The instructions are also easily applicable for any Athearn locomotive.These instructions assume that you have already run the loco and have established that it is working properly before beginning installation. Remember, installing a decoder in a locomotive will not improve its ...

When you program the DS64, you must program all four outputs, even if they are not connected to anything.  A "Virtual" top address can be used to avoid conflicts with actual turnout addresses and other routes. To create a virtual top address use a switch address for your top address that is not used to operate an actual turnout on the layout. The advantage of this is that you can consistently use either the "thrown" or “closed” command to operate all routes, making it easier to remember which position goes with which route to make them work. Since DS64 routes ...

When I get several locos in the same PM42 sub-district, the PM42 seems to shutdown at random times even though I am sure there is no short circuit, what is wrong?1.  The PM42 is set at the factory with a default current trip point of 3 amps for all 4 sub-districts. This is fine in most cases. 2.  If you plan to run more than two or three locomotives in a sub-district, you will need to increase the trip current. 3.  Use the minimum current set point that gives acceptable layout operation, i.e. minimum power interruptions when no short circuits ...

This application note is courtesy of Michael K. Perrin, and addresses the installation of an N-Scale decoder in the Bachmann F40PH (now discontinued).  This note calls for using either DN93 or DN140, both of which have been discontinued.  Current decoders such as the DZ125 or DZ143 and other similar N scale decoders can be used.1) Cut a place for the decoder in the back recess in the frame. Because this is a "sandwich" frame there is no room for the decoder without using a saw or Dremel tool to make a cavity for the decoder. (This is the hardest part of the ...

DT400 can be set up to handle stop commands globally or locally. The default is local control. With local stop, when the EMRG STOP Key is pressed once the loco on the active throttle will stop and when the EMRG STOP Key is pressed a second time, the loco on the other throttle knob will stop. To resume operation, use the throttle knobs to increase speed of the locos from 0. With global stop enabled, pressing the EMRG STOP Key will stop all locos on the layout and you will see the DT400’s track power indicator blinking on and off. ...

What is the meaning of the colored lines and bars which show up in the chart portion of the DigiGroupSetup v1.03 window after pressing the "Start Chan Scan" button? The graphics show the peak signal and average detected while you let the scan run. This may be useful in helping you setup your layout for best Duplex performance. What is the "Group ID" number which is shown in DigiGroupSetup v1.03? The Group ID is typically used in the train show environment, where there may be several wireless networks operating at the same time. The unique Group ID allows new operators ...

It is important to realize that the standard only covers the communication protocol on the track.  As long as it is not extended further than the basic track level communications for train control, creativity will be encouraged rather than stifled. This protocol is very basic and does not require any particular hardware. The Digitrax Complete Train Control System incorporates the DCC protocols for interoperability reasons but has not been held back by them.  Digitrax has developed and marketed automatic reversing boosters, decoders with 128 speed steps and user customizable speed tables, mobile decoders with onboard functions and lighting effects, stationary decoders with sophisticated ...

Q: If my layout is experiencing short because of a thrown switch, how can you reset the switch using DCC? Many Digitrax operators use the PM42 Power Manager, which provides protection to four power sub-districts. One segment of the PM42 is used to control track switch power, with the balance being used for train power. When the inevitable happens and a train runs into a thrown switch, resulting in a short, the PM42 shuts down the track power in that segment, while the track switch power is maintained, allowing you to throw the offending switch. Because the PM42 isolates only ...

Track Power IndicatorThis very small star shaped dot located just above the bar graph display in the LCD on the right side indicates the status of the track power.No indicator = System track power is OFFIndicator On Steady = System track power is ONBlinking Indicator = System is in “STOP” and track power is ON Tetherless IndicatorThe tetherless indicator shows when your throttle is using either infrared or radio communications.L and R Semaphores-Cab SignalingThe L and R Semaphores are used when cab signaling is implemented on the layout. The L and R Semaphores will display the following:

These instructions detail the installation of a wired Digitrax decoder (a DN140 in this example, but many wired decoders may be used) into an Atlas GP35 manufactured by Kato prior to September, 2007.  These units are marked "Japan" on the bottom of the locomotive.  Units marked "China" use a board replacement decodr such as the DN163A2.Installation DiagramNotes:A. Be sure motor leads (Gray & Orange) do not touch frames & have protective insulation in place.B. Be sure frame is straight & mechanism is correctly reassembled & can turn freely without binding.Wired Decoder Installation InstructionsFollow these steps for decoder installation with either ...

SW01 to SW08 are inputs that allow a local switch mounted on the layout to operate the slow motion turnout machine. For example, SW01 when connected to the +VE sensor common (Pin 2 in figure) will reverse the voltages on SMTM1A and SMTM1B to change the position of turnout 1. SW02 controls local turnout 2 , etc. For each connection to +VE sensor common the slow motion turnout machine swaps direction and a Switch message is sent to LocoNet to report the new position of the turnout. This local control can be disconnected by setting OpSw 15 to closed, in ...

Since many Zephyr and Zephyr Xtra Starter Sets are used on smaller railroads, a natural choice for setting up an automatic reversing section would be an AR1. If you have more than one reverse loop, then the PM42 is a better choice. These automatic reversing strategies will work equally well for any Digitrax system using any Digitrax Starter Set.  Alternately for larger railroads, an auto reversing booster such as the DB150 can be used for automatic reversing if the section is large.

Some users prefer to “dispatch” or release all addresses active in their system before shutting down. This can prevent unexpected results when you power up the layout again. 1. Turn track power off: Press the PWR Key followed by the N - Key , the Track Power Indicator on the DT400 and the Track Status Indicator on your command station will go off. 2. Move the command station’s “MODE” switch to the “SLEEP” position. 3. Turn off the power supply to the system. The power to the command station can be left on all the time if desired. In “sleep” ...

Most intermittent operation faults on all layouts, not only DCC ones, are caused by bad electrical connections and poor wheel pickups on locomotives.  Poor electrical contact causes problems with sound decoder operation in particular.  Sound decoder installations usually include a capacitor to store energy to keep the sound going when the decoder briefly loses electrical contact.   When the track is dirty or corroded, it can't transmit the electricity and DCC signal needed to run locomotives.  When the locomotive pick ups are dirty or corroded, they can't pick up the signal from the track.  Check your track cleanliness and quality of wheel pickups ...

I own a Digitrax Starter Set that is now discontinued. Can I still use it and can it be upgraded?LocoNet lets you use all Digitrax LocoNet components in your system no matter when you purchased them. You can continue to use what you already own with new components as they become available. Note:  This will work with all starter sets except for Challenger. If you have a Challenger Set and you want to move up, the best thing to do is to purchase one of the new sets and use the DB100 series booster that came with your Challenger as ...

 OpSw Setup Enter OpSw mode by pressing the OpSw button.  The OPS and ID light will flash alternating RED and GREEN. Use your throttle in SWITCH mode to set switches to thrown or closed to match your desired OpSw setting.  There are currently no published OpSws for the BXPA1. If you erroneously set an OpSw, the BXPA1 can be factory reset by setting OpSw40 = Closed Trip Speed Pot The Trip Speed Pot can be adjusted to set the speed at which auto reversing and power management is resolved.  Turning the pot clockwise will make the speed slower and turning ...

In addition to controlling turnouts via LocoNet with your DT400 throttle or with a computer program such as Railroad & Co., you can use local push buttons to operate turnouts. These buttons can be mounted near a particular turnout on the layout fascia or on a local track diagram. In this way, train crews can operate a turnout with a push of the button. The momentary push buttons are connected to the DS64 inputs marked S1, S2, S3 and S4. The return connection of each push button is made to "+COM. Here, a momentary button is connected to operate Turnout ...

Note: These instructions cover the hardwired installation of any Digitrax decoder with wires into a Kato GP35 H0 Diesel. Currently, the recommended decoder for current production GP35's from Kato are the DH163K0 board replacement decoder.  Using the board replacement decoders are much simpler and cleaner installation than the one described here.Tools Needed for Decoder InstallationYou'll need a few simple tools:1. A soldering iron, preferably temperature controlled.2. Solder3. Screwdriver4. Small diagonal cutters for cutting and stripping small wire5. TweezersMotor Isolation for Kato GP35Carefully remove the loco's shell and weight.To isolate the motor, disconnect the brass strips (motor brushes) from the track pick up ...

Decoder Wire for decoder, lighting & signal installation 90ft 32AWG stranded wire-10 ft lengths in 9 colors

.672” x 1.074” x .259” 17.08mm x 27.28mm x 6.6mm Digitrax Easy Connect 9 Pin Harness 1.5 Amp/2 Amp Peak Current Rating 2 FX3 Functions, 0.5 Amp Total Function Current Rating

.672” x 1.074” x .259” 17.08mm x 27.28mm x 6.6mm Digitrax Easy Connect 9 Pin Harness 1.5 Amp/2 Amp Peak Current Rating 6 FX3 Functions, 0.5 Amp Total Function Current Rating

1 Amp (1.5 Amp Peak) Mobile DCC Decoder Please use 3 step speed tables for all DZ121 & DN121 Series Decoders, because of size constraints in their processors, they do not support 28 step speed tables. Non-directional headlights are NOT available on DN121 Series Decoders. Retired in 2003

1 Amp (1.5 Amp Peak) Mobile DCC Decoder Please use 3 step speed tables for all DZ121 & DN121 Series Decoders, because of size constraints in their processors, they do not support 28 step speed tables. Non-directional headlights are NOT available on DN121 Series Decoders. Retired in 2004

Tiny Super Economical Wired Motor & Function Decoder

Wired Motor & Function Decoder that fits many N and HO Scale Locos.

1 Amp Digital Command Control Mobile Decoder Retired in 1997

1 Amp Wired Mobile Decoder, 4 Functions Technical Note: If using DH142, DN142, DN141K2, DN149K2 series decoder, when F1 is set up for FX, F2 must also be set up as FX (It can’t be used as standard on/off function.) If you want to use a combination of FX & standard on/off functions, please use F1 as the standard on/off function and F2 as the FX function. Retired in 2006

For InterMountain N Scale F7A & B units with wired motors produced after Jan 2014 6 FX3 Functions .472” x 2.165” x .098” 11.98mm x 54.99mm x 2.4 mm Replaces DN163I1D

Fits Intermountain N Scale FP7A with wired motors produced after Jan 2014 6 FX3 Functions 472” x 2.165” x .098” 11.98mm x 54.99mm x 2.4mm

0.5 Amp Wired Mobile Decoder This is one of the earliest decoders produced by Digitrax Some were marked DN82 and some were marked DN82F It did not have a blue wire for lamp common Some of these decoders did not use standard wire colors, please consult the instructions sheet for color coding. Retired in 1994

1 Amp Wired Mobile Decoder, 3 Functions Retired in 1995

1 Amp Wired Mobile Decoder, 3 Functions Retired in 1997

5-pack Digitrax N-Scale Wire Harness

Digitrax N-Scale Wire Harness with 8 Pin plug

1 Amp Wired Mobile Decoder for use in Z, N, HO scales Retired in 1999

1 Amp Wired Mobile Decoder Please use 3 step speed tables for all DZ121 & DN121 Series Decoders, because of size constraints in their processors, they do not support 28 step speed tables. Non-directional headlights are NOT available on DZ121 Decoders. Retired in 2002

Cost effective tiny wired decoder.

Tiny Decoder, 1 Amp Fits in Z, N & HO Locomotives

Fits Many Z, N and HO Scale Locomotives

Tiny wired decoder for many Z, N & HO Applications.

Wired Motor & Function Decoder that fits many Z, N and HO Scale Locos.

Oval 10mm x 18mm 8 Ohm Speaker with wires. Fits many N & HO Scale installations. Used on current production SDN144A0, SDN144A1 & SDN144PS sound decoders.

Round 13mm 8 Ohm Speaker with wires. Fits many N & HO Scale installations. Used on current production SDN144K0A and SDN144K1E sound decoders.

Fits many HO, O & G Scale installations. Also fits in N Scale box cars.

SP282832 - Round 28mm 32 Ohm Speaker with wires. Great for HO installations. Used on current production SFX004, SFX064D, SDH164D & SDH164K1A sound decoders.

SP28288 - Round 28mm 8 Ohm Speaker with wires. Great for HO installations. Used on current production SFX0416 sound and function decoder.

Fits many HO, O & G Scale installations.

Fits many HO, O & G Scale installations.

Digitrax Command Stations use three address ranges available for addressing and programming locomotives. You can use all three address ranges at any time and in any combination you choose.Address 00: The analog address used to run locomotives without decoders. All analog locos (those with no decoders) active on the layout will respond to the speed and direction commands issued to address 00.2 digit addressing: Addresses in the range of 01 through 127. Also called short addressing, 2 digit addressing can be used with any DCC decoder, shown as the two or three digits, with no leading zero, of the address ...

This article courtesy of Ken Bessler, concerning installation of a decoder into earlier Kato C4400W's.  Current produiction of these locomotives use DN163K1C or similar board replacement decoder.I wanted to convert my 2 new Kato AC4400CW's to DCC but there were several problems:1) The recommended PnP decoder, DN163K1a has a chip right where a shell component is. Using this decoder requires shaving off the plastic retainer clip under the exhaust stack. IMHO this is not good as it leaves too little support for the stack.2) My dealer was out of stock of the PnP decoders.3) A quick look inside the loco shows ...

What are the different operational modes available in the PR3? The PR3 is the combination of two previous Digitrax devices: the PR2 decoder programmer and the MS100 LocoNet to computer interface. The PR3 can be configured through manual (control panel buttons) or automatically (software) means to perform any one of the following three operations: a) The PR3 can be configured to function as a stand alone decoder programmer. In this mode the PR3 can program the configuration variables of most DCC decoders and the sound effects of the Digitrax Sound FX sound decoders. b) The PR3 can be configured to ...

Most HO, N & Z Scale model locomotive motors and lamps are designed by the locomotive manufacturers to operate at full speed at 12 volts DC on the track. Digitrax recommends running your DCC command station and boosters at the lowest track voltage possible that provides acceptable operation. The “N Scale (12V)” setting on Digitrax equipment works for most HO, N & Z scale layouts. Some DCC systems made by other companies supply more voltage to the track and are not adjustable. If the track voltage applied exceeds the operating parameters of the locomotive and its lamps, it is possible ...

I am now constructing an N-Scale layout with Digitrax DCC system. I know SE8C and two-heads signal mast supplied by your company are applicable for a entry signal mast for the both of main and siding (branch) lines. However, I don't know how the signal mast is used in the case of "more than two" siding lines. For example, the next picture was taken in Powder River Basin (Converse Jct.) in Wyoming State. TS, Japan In this picture, some two-heads signal (mast) can be seen. In every signal mast, the top signal head will be for a main line. But, ...

If the DB150 unit shuts down occasionally due to a track short circuit: 1. Correct the short circuit condition and the booster will resume normal operation. 2. Turning off the booster when a short occurs is not necessary since it will re-start automatically when the short is cleared. If the DB150 unit shuts down frequently: 1. Move the DB150 so that the heat sink has a flow of cool air. 2. Place the DB150 out of direct radiant heat like sunshine or a room heater. 3. Try direct cooling by using a small fan to blow air onto the heat ...

Will Digitrax work in an outdoor setting to control LGB, Bachmann, and Aristocraft engines on a small layout, possibly in a 20 x 20 area? What starter set would you recommend to run in the area stated? I would like wireless operation. Digitrax will work in that environment, with the same warnings that are associated with all other electrically powered devices and outdoor model railroads that use track power. The command systems must be protected from moisture, the track must be clean and the stationary decoders are not weatherproof. Wireless operation can be either infrared or radio, with radio being ...

The Athearn N-Scale P59PHI was not designed for a plug 'n play or board replacement installation therefore, a wired installation will be necessary. This installation is straightforward if you follow the instructions provided below. There is plenty of room inside the locomotive for this installation. See the Digitrax Decoder Selector on our home page to determine which current production decoder is recommended for this installation. Athearn N-Scale P59PHI Installation Instructions for Digitrax Decoders:1. Remove the locomotive's shell. Note which end of the frame is the front and which is the back.2. Remove the light board that is installed on the ...

Your DT402/DT400 throttle comes from the factory set for “Local” Stop. When you press the EMRG STOP Key , the loco address that is active on your display (the one with the blinking smoke) will stop.When you press the EMRG STOP Key again, the loco address on the other throttle of your DT400 will stop.You can use the OPTN t Key to change the EMRG STOP to “Global” Stop.With global stop option enabled, pressing the EMRG STOP Key will stop all locos on the layout and you will see the throttle's track power indicator blinking on and off.To resume operations, press ...

The Intermountain 2014 release of their F-Units require some special attention when installing a decoder.  There are three locations which require attention to make sure the motor and headlight LED are completely isolated.  If the motor is not insulated, you'll hear a buzzing sound when the locomotive is placed on your layout.  I would suggest trying to program the locomotive on an isolated service mode programming track.  If you're successful in programming, the motor is properly isolated. 1. The motor has to be removed from its mount and Kapton tape needs to be placed from the bottom of the motor ...

This installation procedure is for the DIGITRAX DH166/DH126 decoder. Alternatively, you can use a Digitrax DN166 in this installation. If you use the DN166 the installation will require fewer engine modifications because of the smaller physical size of the decoder.Note any decoder of smaller physical size can be used in this installation.  DN136D, DN166, DZ126, DZ126, DZ146 are all possibilities. After removing the shell from the locomotive chassis, note the color and location of each of the various wires.  All connections must be soldered with rosin core solder and insulated with shrink tubing.We will locate the decoder in the forward ...

Short Address Programming Note When programming the short address (CV01) in your DZ121, the decoder will automatically set CV19 to 0, CV29 to 0, CV 55 to 80, CV56 to 30 & CV57 to 0. This is done to insure compatibility with DCC systems that only recognize short addressing (2 digit mode). When using long addressing (4 digit addressing) these CV's are not affected.After changing the short address (CV01), you will probably want to change CV29 to 06 or another appropriate value based on your operations. You can do this on the programming track or, if you forget, you can ...

Configuring the Duplex Group Password The UR92 ships from the factory with the default Duplex Group Password of 0000, the value that disables password requirements. You may have an occasion when operating in a multisystem environment when you may want to restrict access to your layout and operating system via a tetherless Duplex Throttle. The password for your Duplex Group may be activated or changed: 1. Plug a DT402D or DT500D throttle into the UR92. 2. Press the EXIT key. 3. Press the OPTN key then the EDIT key. 4. Enter a 4-digit number using the numbers on the keypad ...

Digitrax decoders allow for operation on both Digital Command Control (DCC) powered and on traditional Direct Current (DC) powered model railroads.  Decoders from other manufacturers may or may not have this featureModern Digitrax Decoders are shipped with analog functions enabled to allow you to have working functions on locos on either type of layout without changing any CV values.  (Series 3 decoders and later) When a Digitrax Series decoder with analog functions enabled moves from a DCC track section to an analog track section, the functions that were active on DCC will remain active on DC.  For these decoders, CV13 is ...

The DS51K1 is designed specifically for Kato N-Scale turnouts.  Kato manufactures both a #4 and #6 turnout; one DS51K1 will control one Kato turnout solenoid.  In cases where there are two turnouts in a crossover track arrangement, you must use two DS51K1s, each assigned to the same address.Installation of the four decoder wires requires soldering skills.  And, just to make things interesting, Kato uses the colors of black and red for their turnout control wires, while Digitrax uses black and red for the power and data bus.  You will make four connections, two connected to the turnout motor and two ...

The MODE and SCALE switches are used to configure the DCS100 for your railroad. The 3 MODE switch settings are:  RUN is for normal operations. OP is used to customize the DCS100 by changing its option switch settings. SLEEP is used to shutdown the system and all throttles that are plugged in to the system. SCALE Switch (O/G HO N) This switch sets the maximum track voltage limit. 1. Set the DCS100's SCALE switch to the scale you are running (N, HO, O\G). Use the lowest setting (N, HO, or O/G) that will run your layout. 2. Set the MODE switch ...

DT400 Series Throttles - Make F2 Latching or Non-latching The F2 button on the DT400 is meant to control locomotive whistles and horns, so it is configured to be "momentary" or non-latching.  This means that the key will activate the horn or other function for as long as you hold the key down and stop when it is released. This was done to facilitate the use of a playable whistle in sound decoders. If you are not using F2 for this purpose on your layout, you can change the way the F2 key on the throttle works so that it latches on and ...

What's the difference between the PM42 and the PM4?The PM42 is an improved version of the PM4. We added 2 faster short circuit detection sensitivity settings and revamped the manual. Get the benefits of short circuit management and auto reversing without adding more boosters! PM42 Quad Power Manager lets you use a single booster and divide its output into 4 power sub-districts for automatic reversing &/or to improve operation by preempting booster shutdown when a short circuit is detected by the PM42. If you want to improve operation but don't need the added power (or expense) of adding a booster, ...

Many thanks to Bob Dattore for this application note!This app note details using a DN142 decoder for the installation.  This decoder is no longer in production but the following decoders would work as well:  DN135D, DN163, DZ123, DZ125, DZ143.  Any decoder that is small enough to fit could be used.The Problem:  Atlas RS1's (and RS3's & RSD4/5's) are hard to install Digitrax decoders in. There is no easy drop-in or light board replacement with back-emf capability.I have installed several Atlas Dual Mode decoders in these popular hard to fit narrow, low hood diesels with ease, by replacing the original light ...

Digitrax Command Stations can operate one locomotive on your layout that does not have a decoder installed. This loco is called an "analog," "conventional," or "non-DCC equipped" locomotive. To operate an analog locomotive with Digitrax you will use address 00 to send commands to the locomotive.  The magic that makes this happen is called zero stretching. With Zero Stretching, an analog locomotive going forward receives an unusually long positive voltage, followed by a very short negative voltage. The much larger positive voltage ensures the locomotive moves forward. The brief negative pulse causes a low buzzing that will vary with the speed of the locomotive. This method ...

Digitrax boosters have maximum output current limits of either 5 or 8 amps. The actual continuous output current that your booster will provide to the layout depends on several factors including the input supply voltage, the ambient room temperature and air flow over the booster's heat sink. Higher input voltages increase the amount of heat that must be dissipated by the booster's heat sink. If the heat sink does not get enough air flow to allow for heat dissipation, the booster will eventually reach an over temperature state and shut down. A small fan blowing across the heat sink on ...

Dispatching is a special feature incorporated in the LocoNet "language" to meet the needs of operators that wish to enforce a strict discipline in how operators gain access to locomotives during an operating session.Dispatching also lets you run MUs with basic throttles (such as the Utility Throttle series) that can't set up their own MU's and run four digit addresses on basic throttles that only have two digit capability (such as UT1 and UT2). It also lets you have newcomers run trains on the layout without giving them access to the entire operation.When you dispatch a locomotive address or MU ...

If Zephyr DCS50/DCS51’s display shows FuLL this means that it has reached the limit of 10 (20 for the Zephyr Xtra) locomotive addresses that it can manage at one time. If you want to select additional addresses, you will need to release one or more loco addresses before you will be able to select other locomotives to run.The DCS50/DCS51 runs a “purging” routine that helps eliminate addresses that have not been used for a period of time to make slots available for running other addresses.If you see this "FuLL" message while you are operating, you can release locos that you ...

We have designed a layout at my place with double main line with reverse loop at each end. Plus there is a branch line with two reverse loops that in one loop is connected to the main line. The main lines stay double track even at the split. The branch stays single with only one connection with the main. My plans where to use the AR1 for all my reverse loops and the PM42 for my power control. What if any problems do you see with all these loops? Nothing, if you can guarantee that at any given time only ...

When DCC locos enter a brake section with braking on, they will receive braking commands from the command station instead of normal DCC operating commands. DCC locos in this braking section will come to a stop. When you throw the switch to allow normal DCC commands, the DCC locos will resume normal operation. Once the DCC loco has left the brake section under normal DCC power, simply return the switch to the break position so that the next DCC loco will stop in the section. This is useful if you want to have trains stop at stations around the layout ...

The Track Power indicator on your DT402 display shows the track power status. There is also a Track Status light on your Command Station. If the track power indicator is lit then track power is on. To turn the track power on or off: 1. Press the PWR key on the DT402. You will see a screen similar to the one below. You will now be able to toggle the track power on/off: 2. Press the N/- key to toggle the track power off. The Track Power Indicator on your DT402 and on your Command Station will go off. 3. ...

Wired Mobile Decoder with SoundFX™+Accessory type functions for most HO scale Locomotives. 1. Connect the Red and Black track wires from the 7 connector Track and Function leads to the locomotive track power connections. 2. Connect the function leads that are to be used from the 7 conductor Track and Function wire set. Note that to be able to readback Sound FX CV's a combination of function lead loads of at least 60mA at 12volts should be connected to these function leads. Insulate the unused function leads so they cannot short to the locomotive frame or track power. 3. Mount ...

Zephyr Xtra (DCS51) and Zephyr (DCS50) systems can program Soundtraxx Tsunami decoders using Blast Mode Programming on the Mainline.  Blast Mode Programming will program EVERYTHING sitting on the main line track so, you MUST remove everything from the track that you are not programming or use an isolated piece of track connected to Rail A & B. NOTE: Track power must be ON during Blast Mode Programming.  Blast Mode programming will work with all sound decoders not just Tsunami. You will not be able to read back CVs using Blast Mode Programming.  To use Blast Mode Programming with Zephyr, close ...

I have an extensive collection of Z-scale locomotives (some are older (15-20 years) Z-Scale Maerklin equipment).  Can I convert the locos to Digitrax, or must I buy some other brand of loco to use Digitrax?Maybe yes, maybe no.  It depends upon the size of the locomotive and how much space is inside.There are several Z-Scale layouts that use Digitrax decoders.  Z scale railroaders are very persistent and precise so, they are often able to install decoders where members of other scales would fear to tread.  Digitrax continues to design smaller and smaller decoders aimed at the Z scale market.  Z Scale ...

Most modern command stations and decoders are set up to run 28/128 speed steps.  If you are using older command stations or decoders you may need to adjust one or the other to get the trains to run.Why are more speed steps better?The reason you want to use a command station and decoders with 128 speed steps is for smoother speed control of your locomotives.   Digital command control signals are just that, digital.  When you send speed commands with your throttle, you are sending digital instructions telling the decoder to change from the current speed to a different speed.  When ...

This program allows monitoring of LocoNet message traffic and operations. It is available on our downloads page as a ZIP file and is provided for Digitrax customer convenience. This utility is provided on an as-is basis for users with Windows based machines configured to work with this software, and the ability to perform the setup and operation tasks detailed below. Techsupport is not configured to diagnose issues related to operating system, hardware, configuration or other possible problem areas that may cause problems with running these utilities.   This program allows monitoring of LocoNet message traffic and operations. a) Copy this ...

Dispatching is a special feature incorporated in the LocoNet language to meet the needs of operators that wish to enforce a strict discipline in how operators gain access to locomotives during an operating session. Dispatching also lets you run consists with basic throttles that can't set up their own consists and run four digit addresses on basic throttles that only have two digit capability. It lets you have newcomers run trains on the layout without giving them access to the entire operation. When you dispatch a locomotive address or consist to your LocoNet system, you make it available to be ...

Setting Duplex Group Name You can use the DT402D to edit the UR92’s Duplex Group name to one you prefer. Note that this change is optional, and the UR92 factory default will always work out of the box.   The Duplex Group Name is stored in non-volatile memory and is remembered even when unpowered or disconnected from your system.   You should have all UR92s connected prior to changing the Group name or they will automatically renegotiate and may change the preferred name to a default.  1. Connect the DT402D or DT500D to the front RJ12 jack of any UR92 ...

My PM42s seem to correctly trip on track shorts and auto-reverse reliably, but the power briefly drops out during these events, and when the PM42s attempt a fault recovery into a persistent short circuit, why is this?No power on earth can stop the track voltage of the booster from collapsing to a low value when a true short circuit is present. This is simply Ohm’s law in action!Actual track voltage seen depends on: the loop resistance of the short circuit, the current capacity of the booster and power supply and whether the Booster employs "smart" fault detection and recovery along ...

The factory setting for Op#1 for all DT300 throttles is Op#1=x01. This option controls Tracking, Fast Clock Display, Key/Knob Clicks and Stop, local/global.Ballistic or Straight Line TrackingWith ballistic tracking, the faster you rotate the throttle knob, the faster the data changes in the throttle. When ballistic tracking is enabled so are typematic keys. With typematic keys, when you press and hold the Y/+ or N/- keys, the values will continue to increase or decrease without having to do a separate key press for each increment. Your DT300 was shipped with ballistic tracking as the factory default setting.With straight line tracking ...

1) Remove locomotive shell following Roundhouse instructions.2) There are two large diodes, one on each side of the rectangular light board. Remove them.3) The two LEDs are wired to this light board, one on each side with black and gray wires on each LED. Reverse the black and gray wires on the board from each LED (gray to where black was and black to where gray was.4) Remove the dummy eight pin plug and insert the eight pin DCC medium plug of a Digitrax DZ1xxPS decoder with the orange wire going to #1 on the light board.5) Reinstall locomotive shell.FAILURE ...

Shutting Down the System When you are finished with your sessionDispatching All Locomotive Addresses Some users prefer to “dispatch” or release all addresses active in their system before shutting down. This can prevent unexpected results when you power up the layout again. 1. Turn track power off: Press the PWR Key followed by the N - Key , the Track Power Indicator on the DT400 and the Track Status Indicator on your command station will go off. 2. Move the DB150 command station’s “MODE” switch to the “SLEEP” position. 3. Turn off the power supply to the system. Leaving the ...

  There are three different ways to power the DS64.  Track power (Trk A and Trk B), Auxiliary power (AX1(-) and AX2(+)) and power through the rear modular power connector.  Connect the Trk A and Trk B screw terminals of the Power and Track Connections to the corresponding Rail A and Rail B track connections.  The PS14 power supply can be used with Auxiliary or the rear modular power connector.  The DS64 requires 300mA for proper operation.  Only one DS64 can be powered per PS14.  A generic DC power supply between 12-16vdc and 300mA can be connected to a DS64 ...

To control the speed of a locomotive:1. Select the loco address on the Zephyr.2.  Place the reverse lever [2] into either forward or reverse.3. Turn the Throttle Knob  [1] clockwise to increase speed and counterclockwise to decrease speed. Setting Speed LimitsYou can limit the speed on any locomotive controlled by the DCS50. This feature is very useful if you are running your layout with young children who want to make the trains GO FAST!!! By setting a reasonable speed limit on the throttles used by the children, everyone can have more fun with the trains.To set a “speed limit” for ...

There is a potential problem using the DCC socket on the Life Like Proto2000 S-1. While the trucks and track pick-ups are isolated from the frame, there is a brass grounding lug attached to the motor's lower brush cap which makes electrical contact between the lower motor brush and the frame.  As a result if the wheels come in contact with the frame a short occurs and the decoder may be damaged! We recommend one of two work-arounds. 1) If you choose to use the 8 pin DCC plug, isolate the bottom motor brush from the frame of the locomotive ...

1. Strip the insulation from the red, green, black and yellow wires on the harness. The blue and white wires are not used and may be cut off the harness if you wish.2. Twist the red and yellow wires together. Twist the black and green wires together. 3. To test motor operation, hook up the wires according to the directions in the Digitrax Decoder Manual. One of the two center LEDs will light as the motor voltage increases from the decoder. Change direction and the other LED will light. 4. To test other decoder functions connect the LT-1 to the ...

Bring Your Locomotive to a Compete Stop Turn the Throttle Knob that the loco address is selected on counterclockwise until the speed display shows 00 and the loco stops moving. This lets you slow down your loco and stop it in a prototypical manner.If you have set up deceleration for the loco and you move the throttle knob to 0% speed, your loco will slow down and come to a stop at the programmed deceleration CV value.   We strongly recommend that you run your locos with the factory default of no deceleration until you are familiar with your system. If ...

Shutting Down Your Zephyr when you are finished running.Some users prefer to release all addresses active in their system before shutting down. This can prevent unexpected results when you power up the layout again.  There are two ways to do this. ________________________________________________________________________________________________________________To release addresses one at a time (this is optional):1. Press the LOCO key. 2. Enter the loco address on the numeric keypad. The display will flash the Function Indicator Dot and the loco address. Press the LOCO key again.3. Set the Throttle Knob to STOP.4. Press the EXIT key.5. Repeat for all locos/addresses used in your session._____________________________________________________________________________________________________Alternately, you can clear all ...

These are the basic DT400 and DT402 series throttle operating instructions designed to get you “up and running” quickly and to minimize your “frustration level” as you learn to use the throttle.   Turning Track Status On and Off To run your layout you must be sure track power and track status are both ON.  Follow these steps with your DT400 or DT402 series throttle to do this. Press the "PWR" key on the bottom left side of the throttle. The words “+ON  -OFF” will come on in the display. Press the “Y +” key quickly and you should see the ...

Railroad signaling works based on detection of trains on the railroad.  If a train is detected, then the signal system goes into action, setting up indications that let show that the track section is occupied and warn other trains that the section is occupied.  At a grade crossing where a railroad and a highway intersect, the presence of a train starts the crossing signals and lowers the gates in time to stop highway traffic so the train can pass.In the case of real railroads, detection is easy, since the rails are naturally insulated from each other and either a locomotive or ...

The DH163 series decoders are set up at the factory to control six function outputs. The DH163 is configured to control the forward and reverse lights on the locomotive through the white lead and yellow lead using Function 0 (F0F-forward and F0R-reverse) for directional lighting. Functions F1(Green) and F2 (Violet) are part of the harness for easy hookup. F3 and F4 are also available on the decoder board. These can be accessed by snipping the shrink wrap and peeling it back to expose the solder pads that control these functions: To use these functions, solder a wire from the pad ...

Clarifications of UR93 and DT602D/UT6D Duplex RF and network performance: The new UR93 and DT602D and UT6D throttles employ the new Digitrax designed and manufactured RF28 Modular Certified 2.4GHz transceiver module. The RF28 is configured to interoperate with existing Digitrax Duplex UR92 LocoNet access points and e.g. DT500D and UT4D throttles worldwide. All Duplex units employ IEEE 802.15.4 PHY/MAC compatible devices using 2.4GHz Direct Sequence Spread- Spectrum (DSSS) modulation. The RF28 was developed for: a)  Smaller size. The venerable RF24 could not fit in the small UT6D, and this case was designed in 2017, so a new smaller Duplex support ...

What is the physical size of the BDL168? The board itself approximately measures 3 3/4" wide by 3 5/8" long by 1 1/4" high. For those who use metric, it is 94mm by 92mm by 30mm. In addition to the board itself, the edge connector measures 4 1/32" (112mm) by 3/8" (10mm); it has edge connector pins which make the connector 5/8" wide (18mm). The edge connector pins will need additional clearance for the connected wires. Users have found that the heavier bus wires used in most applications are difficult to connect to the edge pin connector; in ths situation, ...

The DB150 has many customizable system operation options that you can set. The DB150's power up defaults are fine for most applications and the DB150 will run just fine right out of the box. These options are provided for those individuals who want more flexibility in setting up their operations. The factory default setting for all DB150 option switches is t or thrown except for 5, 17, 25, 33 and 34 which are closed ("c"). Changing DB150 Option Switches 1. Consult DB150 Option Switch Table to determine which DB150 option switches you want to change. 2. Move the right toggle switch on the ...

Installing the TF4 in the Loco or Rolling Stock1. Connect the TF4's RED and BLACK wires to the matching RED and BLACK track feed wires of an installed DCC mobile decoder.2. If the TF4 is used by itself, for example in a caboose or box car without a DCC mobile decoder installed, connect the TF4's RED wire to the right hand track pickup and the TF24s BLACK wire to the left side track pickup.3. No other parts are required to set up the transponder current pulses, since this is self-contained in the TF4.4. Install the lamps using the TF4's blue, ...

This Application note shows how Marklin Users can have the power and reliability of Digitrax boosters along with their Marklin command stations! Notes: 1. Before applying power to the booster, use a short length of wire to short the 2 gray terminals (SYNC & GROUND) on the DB100. This forces the DB100 into the booster mode when the power is applied to it. Set the MODE switch to "P/R" for auto reversing operation or to "RUN" for normal booster operation. 2. Make a cable with 6 conductor RJ12 cable with a 6 conductor male plug on the DB100 end and ...

The DN163A0 is set up at the factory to control six functions. The unit is prewired with two golden-white LEDs set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the industry (you can use any color you like). These colors are important if you ...

The DN163K1D is set up at the factory to control six functions. The unit is prewired with two white LED's set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the industry (you can use any color you like). These colors are important if you ...

Is this part of the instructions sheet?  If so, we don't need it here?  ZIThe DN163K2 is set up at the factory to control six functions. The unit is prewired with two golden-white LEDs set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the ...

The DH165Q1 is set up at the factory to control six function outputs. The DH165Q1 is configured to control the forward-headlight F0F/white lead and reverse-headlight F0R/yellow lead for directional lighting. These two headlight function leads are current regulated for LEDs or lamps, with factory setting of approx 15mA, with no resistors required. Cut the ADJ link to increase headlight current to approx 30mA- see fig 5. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) are full track voltage and can be used by soldering a wire from the pad for the function you wish to use to the ...

The DN163A1 is set up at the factory to control six functions. The unit is prewired with two golden-white LEDs set up for directional lighting as F0F/F0F+ for the front light and F0R/F0R+ for the rear light. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) can be used by soldering a wire from the pad for the function you wish to use to the lamp (or other function) you wish to control. The wire colors indicated are the standard color code used in the industry (you can use any color you like). These colors are important if you ...

Preparation 1. Carefully remove the locomotive's shell from the frame. Note the orientation for proper reinstallation. (Figure 1) 2. Remove the four track power pickup wires clipped to the lightboard (2 on each side) (Figure 2) Carefully pull the brass motor clips from under the track power "staples" on the lightboard. 3. Unscrew the lightboard screws to release PCB from the frame. Decoder Board Installation 4. Physically secure the DH165K0 decoder PCB with the lightboard screws. 5. Attach the four track power pickup wires by shortening and stripping each wire (2 on each end) and soldering these wires to each ...

The LT1 is a simple decoder tester. Decoder Testing Instructions1. Prepare the cable for use in the testing procedure, by stripping the insulation from the Red, Green, Black, and Yellow wires. The Blue and White wires are not used and can be cut off the harness.2. Twist the RED and YELLOW wires together. Twist the BLACK and GREEN wires together. 3. Hook up decoder as shown in Diagram 2.4. Use your throttle to select the decoder and run it in the forward direction.5. One of the two center LEDs will light as the motor voltage from the decoder increases. Use ...

  Digitrax UT4 Throttle Operating Instructions by Dan Bourque     Selecting a locomotive or consist 1.         Dial the 4-digit locomotive address into the “LOCO ADDRESS” dials             - For a consist, the address will normally be the lead locomotive             - For a 3-digit locomotive number, use “0” for the first digit 2.         Plug the throttle into any receptacle on the layout fascia (e.g. Digitrax UP5) 3.         Press the “SEL” key, the ST light on the throttle should turn green 4.         Move the direction selector on the throttle to either “R” or “F” 5.         Move the ...

The DH165K0 is set up at the factory to control six function outputs. The DH165K0 is configured to control the forward-headlight F0F/white lead and reverse-headlight F0R/yellow lead for directional lighting. These two headlight function leads are current regulated for LEDs or lamps, with factory setting of approx 15mA, with no resistors required. Cut the ADJ link to increase headlight current to approx 30mA- see fig 5. Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) are full track voltage and can be used by soldering a wire from the pad for the function you wish to use to the ...

Switch Mode is used for sending commands to accessory decoders and for changing Option Switches (OpSw) in your DCS50. The most common use of switch mode is for operating turnouts (track switches).To change the position of a turnout:This note assumes that you have already installed and programmed turnouts and turnout decoders on your layout.  Each turnout is connected to a stationary decoder that controls the operation of that turnout.  There are several different stationary decoders for this purpose such as DS64 and others.  Please see the related articles below.1. Press the SWITCH Key. 2. The last switch address selected by ...

The DH165A0 is set up at the factory to control six function outputs. The DH165A0 is configured to control the forward-headlight F0F/white lead and reverse-headlight F0R/yellow lead for directional lighting. These two headlight function leads are current regulated for LEDs or lamps, with factory setting of approx 15mA, with no resistors required. Cut the ADJ link to increase headlight current to approx 30mA (see figure below). Functions F1 (Green), F2 (Violet), F3 (Brown) and F4 (White/Yellow) are full track voltage and can be used by soldering a wire from the pad for the function you wish to use to the ...

Life-Like Proto 2000 locomotives with number board lights have the number board bulbs wired to their 8-pin DCC plug using pins 4 and 5. This causes no problems with DC operation but causes a path from the rail pickup to the gray motor lead when a decoder is installed resulting in erratic operation and decoder failure.This is a known problem in the Proto 2000 GP60, SD60M and LifeLike GP38-2.  The DH165L0 uses a current limiter set to control one incandescent bulb on the front (FOF) and one on the rear (FOR) and putting the removed number board bulb on either ...

I don't understand what the white cam lead gets hooked up to. Some model steam locomotives are equipped with, or can be equipped with, a cam arrangement which coordinates the sound to the rotation of the drivers creating chuffing. As the wheels turn, a switch opens and closes, operating the chuff sound produced by the sound decoder. The white wire goes from the decoder to a microswitch which is operated by a cam that is mounted on the axle of one of the drivers. In operation, when the white wire senses the DCC track signal, it operates the chuff sound ...

These simple instructions will help you get up and running quickly. A full description of all controls and technical reference information are included later in this knowledge base. This section assumes that you are using a new set straight out of the box.1. Hook up the wires from the track to the RAIL A & RAIL B terminals on the DCS50. Insert the wire from one rail of the track into the RAIL A terminal on the back of the DCS50. Insert the wire from the other rail of the track into the RAIL B terminal. Turn the screw counter ...

Some internet experts INSIST that DCC bus wires must be twisted, presumably to prevent crosstalk and interference. Is this required by Digitrax?Digitrax does not require twisted wires on feeders etc, but suggests appropriate wire sizes and keeping feeder run lengths to a minimum because of resistance/power loss issues.

LocoNet's "ethernet like" architecture seems interesting and more advanced than the systems used by other DCC manufacturers. But, at the numbers we are talking about (a few controllers and perhaps 10-20 decoders), does it really make a difference?If your system operates with a few throttles and other devices attached any of the commercially available systems will work today. But what about tomorrow? Remember when a hard-drive bigger than 32Mb seemed excessive- and remember when DOS had to change to 16bit FATs/ directories? Also, the LBA access change at 540Mb also once seemed unthinkable!!The network structure of LocoNet is very important ...

There are times when it is necessary to reset the Super Empire Builder. Because this is a system reset, there are special instructions: There are different levels of system reset. OpSw 36: Clears all mobile decoder information, including locomotive consists. OpSw 38: Clears the locomotive roster (such as when you receive a "slot=max" error report). OpSw 39: Full reset, clears all internal memory states. The factory default setting for all DB150 option switches is t or "thrown" The Initial Procedure 1. Determine which DB150 option switch you want to change, 36, 38 or 39. 2. Move the Mode toggle switch on ...

Instructions below are for both DCS100 & DCS200 (DCS200 omitted in text for clarity).1. Refer to the DCS100 Option Switch Table to decide which option switches you want to change. Also note that there are special instructions for OpSw's 36, 37, 38, & 39. 2. Move the MODE toggle switch on the front of the DCS100 into the "OP" position . The LocoNet Railsync will go inactive & all other boosters plugged in to LocoNet, including the one that is built into the DCS100, will shut down. 3. Disconnect LocoNet from the DCS100 you are configuring. 4. Connect your DT300 ...

Changing of the value of a DS54 Configuration Variable using your Zephyr Xtra (DCS51) or Zephyr(DCS50) is easy if you follow the steps listed below. 1) Disconnect the DS54 from the LocoNet, aux power source, all inputs and all outputs. 2) Short the pins of the Enable Link. 3) Connect the DS54 track terminal inputs to the Zephyr isolated programming track. 4) Connect the yellow (feedback) wire from any DS54 Output (A, B, C or D) to either rail of the Zephyr isolated programming track. 5) Zephyr Programming Steps.  6) Remove yellow (feedback) wire connecting the output connector to the Zephyr isolated programming track. ...

  Changing the value of a DS54 Configuration Variable with a DT400 is easy if you follow the steps listed below. 1) Disconnect the DS54 from the LocoNet, aux power source, all inputs and all outputs. 2) Short the pins of the Enable Link. 3) Connect the DS54 track terminal inputs to the isolated programming track.4) Connect the yellow (feedback) wire from any DS54 Output (A, B, C or D) to either rail of the isolated programming track. 5) DT400 Programming Steps:  6) Remove the yellow feedback wire connecting the output connector to the isolated programming track.7) Remove the wires ...

Note:  These instructions are the same for DCS100 & DCS200 (DCS200 omitted for clarity).1. Refer to the DCS100 Option Switch Table to decide which option switches you want to change. Also note that there are special instructions for OpSw's 36, 37, 38, & 39. 2. Move the MODE toggle switch on the front of the DCS100 into the "OP" position . The LocoNet Railsync will go inactive & all other boosters plugged in to LocoNet, including the one that is built into the DCS100, will shut down. 3. Disconnect LocoNet from the DCS100 you are configuring. 4. Connect your DT400 ...

A slot is a memory location in the command station that holds an active decoder address.  The number of slots is the number of locomotives that the command station can support in operation at a time. When the available slots are filled with decoder addresses, trying to select another locomotive address to run generates the "slot=max" error code.  When all the slots are full you can't select another address until one is released from the system. See Clearing your Command Station's Mobile Decoder Slots below for how to prevent this from happening.The DCS100 Command Station/Booster that is included with Super Chief Xtra and other ...

The DN163M0 is set up at the factory to control six functions. The unit is prewired with one golden-white LED (shown in figure below) for the headlight and set up as Function 0 (F0F-forward). Function outputs F0F/Yellow, F1/Green, F2/Violet, F3/Brown and F4/White/Yellow are available on the decoder and can be used by soldering wires from the pads indicated to the lights (or other functions) you wish to control. CAUTION: When adding function wires, be very careful that the wires you add do not come into contact with any other pads or components on the board where they might create a ...

I have a Broadway Limited Import diesel locomotive equipped with factory DCC and Sound. Every time I turn on my Digitrax Zephyr DCS50 the engine starts to short out. It begins to slow down and then jerks a little and sometimes it stops completely. My Zephyr shows a line of flickering zeros across the dial and the engine decoder number even flickers on and off at times. I have checked all terminal connections and for foreign matter on the track but have not had any success in solving the problem.I have taken all cars off the track to make sure ...

When purchasing a loco that says its decoder ready, exactly what is implied? Does this mean wires can be wired into the numbered locations and nothing else is needed except to remove jumpers?As with any technology, it takes time for standardized terminology to become established.  Although DCC is almost twenty years old, there are still some gray areas with descriptions.  It really depends upon the individual manufacturer, and within one manufacturer's product line there can be variances also.  There are several types of locomotive decoder installations and you may find that these terms are not applied by all manufacturers in ...

Your DZ143ps decoder has been suggested for my Broadway Limited Blueline PRR J1a. I want to install a Seuthe smoke generator (#100 10-16v,120ma), which was recommended. I don't want to connect it directly to the track power because it will run all the time. Is there a way to connect it to DZ143PS so I can turn it on and off? Yes. The DZ143 series have a total of four function outputs, two are for the front and rear headlights and two are for additional functions. F1 controls the green wire output of the decoder, F2 controls the purple wire ...

Digitrax command stations have Option Switches that care used to customize their operation.  Command Station option switches should not be changed unless you fully understand what you are trying to accomplish.  Information on these Option Switches is included in each command station's manual.Be sure that you are changing the correct Command Station Option Switches as the unit can be crippled by closing the wrong switches.  NEVER CLOSE OPTION SWITCH #1!!Clearing your Command Station's Mobile Decoder SlotsMost command station problems are caused by filling up the command station's available slots by the following:1.  Operators failing to zero the speed of unused ...

If you are operating in a show environment where there are other model railroads operating which use Digitrax wireless throttles, you must insure that your railroad's LocoNet ID is different from others that are also present. Your throttle will log on to the LocoNet ID offered by compatible infrared or radio receiver it sees when plugged in to LocoNet. The default LocoNet ID is 00. It may be necessary to change the LocoNet ID if more than one club is operating in close proximity at a train show so that the commands sent by one club will not interfere with ...

Q: What is the basic configuration and OpSw settings for a section of the PM42 when configured for circuit breaker control? A:  The PM42 is a 4 section multi-purpose device where each of the four sections can be individually configured to act as either a circuit breaker, or automatic reverse loop controller. The PM42 monitors the current flow to the rails and interrupts the connection when it senses that the current demands exceed the upper allowable current level determined by the User controllable Option Switch (OpSw) settings. The power flow of a layout's command control system starts with the command station, or ...

Application Note: Con-Cor HO-Scale Zephyr steps needed for the DZ125PS decoder installation Step 1: Carefully remove the body from the frame. There are four clips along each side of the body. (See red arrows) We have found if you start at the rear of the body with a small flathead screwdriver and carefully pry the body outward to remove the back clip, you can move the screwdriver forward to release the others. Once the body is completely removed, carefully lift the light board from its holders on the bulkheads. (See blue arrows) Be very careful as the pins that hold ...

  I have an "old" vintage mid 1970's Atlas Turntable and I need to know how to wire the bridge track using DCC. Does it need an autoreversing unit or not?No. The Atlas H0 turntable is an evergreen for the model railroad hobby. It was easy to install and simple to wire, making it quite popular.Power is fed to the turntable bridge by connecting the track power feeds (black and red) individually to two screw terminals; these terminals are built into the portion of the Atlas turntable base which also includes the turntable manual crank handle. The turntable itself is ...

There are 1024 different CVs that have been defined to handle many characteristics you might want to use for your locomotives. Your decoder manual has a complete listing of CVs that are available in specific decoders, what they do and suggested values for each CV. 1. Place the decoder equipped locomotive you want to program on the programming track. If you are using operations mode programming, the loco you want to program can be anywhere on the layout but it must have a decoder that is capable of ops mode programming installed. 2. Enter Program Mode by pressing the PROG ...

When the BDL168 is connected to LocoNet, it will communicate coded detection information to the system. If you wish to report BDL168 status to LocoNet and attached devices or computers that can interpret these messages, you will probably want to set up a unique board address for each BDL168. This is done so that the BDL168 Board ID does not conflict with the Board ID of other devices on the railroad. Board addresses can range from 01 to 999. It is recommended that you make a record of the addresses you use for all devices connected to your layout. Setting ...

DCS50’s Jump A & B ports can host two DC power packs that work as additional throttles to control DCC locomotives.You begin with an operating DCS50 attached to your layout.   In addition to the throttle built into the DCS50, you can create a LocoNet to add additional Digitrax throttles and other Digitrax devices.  Jump Ports:You can also connect up one or two smooth DC power packs as shown in the following illustration.  These power packs must also be powered, since the Zephyr jump throttle connections detect the voltage level from the individual power pack(s) and makes adjustments to the command control ...

I want to run a small 12V -16V AC motor via DCC and am not sure if you have a decoder for this and if so how to connect up.For Variable Speed:Some Digitrax decoders, such as the DG583S, can be programmed to operate AC motors. When you program CV61 to a value of 004, Digitrax decoders with split field motor drive capabilities will convert their motor leads to drive a "split field" AC motor instead of the default DC motor. This lets you run Maerklin 3-pole AC motors and similar motors in a number of locos built in Europe with ...

The term smooth DC is used to describe the power provided to the layout by conventional model railroad power packs (analog transformers). Traditional model railroad power packs convert household line current into 12-18 volt current to power your model railroad. Voltage is supplied to the track, and as the voltage increases, the speed of the locomotive's motor increases, which makes it run down the tracks at faster speeds. Some power packs put out only AC (alternating current), while others put out DC (direct current) and AC (for accessories such as track switches and building lights). AC powered trains tend to ...

In addition to the locomotive address, there are different Configuration Variables (CV's) that have been defined to handle many characteristics you might want to use for your locomotives. These include operational characteristics such as acceleration, headlight functions and others. The manual for each decoder type has a complete listing of CVs that are available in specific decoders, what they do and the suggested values for each CV. Simpler decoders have few CVs while advanced decoders may have many different CVs 1. Place the decoder equipped locomotive you want to program on the programming track If you are using operations mode ...

Digitrax uses CV33-CV46 to handle remapping according to published standards.The CV values that are permitted for function remapping are limited to 8 bits, a maximum value of 255. Therefore only 8 functions can be mapped to each function key.Function remapping is easy! Just follow these simple steps:1. Locate the row for the Throttle Function Key [chart below] that you want to use.2. Locate the column of the Function Lead Color (number) you want to control.3. Note the value at the intersection of the row and column.4. Program that value into the the CV listed next to the Throttle Function Key. ...

To select and run a DCC equipped locomotive with a known address follow these steps:1. Set the DCS50's Throttle Knob [1] to STOP. 2. Place a DCC equipped locomotive (one with a decoder installed) on your digital layout that is controlled by your DCS50. In this example we assume that you have a new Digitrax decoder that is factory programmed to address 03. If your decoder is using a different address, simply use that address as you follow these instructions.3. Check the DCS50's Track Status Indicator Dot [4] to be sure that track power is turned on. Press the POWER ...

Current production Digitrax decoders use the following numbering system: The first character means that it is a digital decoder. This is always a “D”. The second character indicates the decoder’s physical size. This is based on the smallest "scale" the decoder is designed to fit. This will be a Z, N, H, or G. The third character is the current rating of the decoder. This will be a 1, 2, 3, 4 or 5. We designate 1.25 & 1.5 amp decoders as 1s and 3.5 amp decoders as 3s for simplicity. The fourth character indicates how many functions, including directional ...

BD4 Output Each BD4 is situated between the PM42 Power Manager and the railroad. The DCC signal passes from the DCS50 Zephyr, through the Power Manager, through the BD4 to the track to the locomotive. When a locomotive (or equipped car) is present in a track segment, the BD4 also sends out occupancy information, in two ways. Occupancy Information Output LED1 The LED1 10-pin header is for testing the status of power to the rails and block occupancy with the LED indicator which is included with the BD4. The LED1 can also be used for panel indicator lights using LED's. ...

LNWI Security Considerations: Enabling and Customizing WPA2 Security The LNWI has the option of enabling WPA2 security to require a passcode to connect to the LNWI SSID.  The primary purpose of this passcode is to limit access to the LNWI in a public setting.  This is designed to operate in a similar function to the passcode options for Digitrax Duplex Radio. Using an unsecured connection poses minimal threat to LocoNet access as the LNWI only utilizes a limited number of LocoNet commands.  The LNWI does not have access to programming capabilities or other advanced LocoNet capabilities on your layout.  No ...

We have discovered during a conversion of an earlier Minitrix V60 diesel that the 6-pin socket is not always wired correctly for conversion to DCC. Apparently, earlier Minitrix locomotives equipped with this socket were wired for use with Selectrix decoders. You should examine the connections from the locomotive to the 6-pin plug prior to installing the DZ125IN.

What are the physical dimensions of the BD4 Quad Occupancy Detector? The longest dimension is 3.48 inches. The shortest dimension is 1.03 inches. Height at bridge rectifiers .842 inches and the height with the block monitor installed is 1.062 inches. Remember to allow for wire clearance at the screw terminal end (for the block detection wires) and also allow for vertical clearance for the DS1 and LED1 plug connections at the other end.

How do you wire an AR1 with a BD4 so that you get block detection within the reverse loop and without the BD4 permanently detecting the AR1? It should be wired with the AR1 between the power source and the BD4. All four detection sections of the BD4 will have to be inside the reverse loop.

Determines The Type of Turnouts You Can OperateOpSw 01 defines the output type (static or pulse) for the decoder. Thrown (factory default) for pulse output mode to operate three wire (twin coil type) PecoTM or Atlas Snap SwitchesTM or two wire bi-polar type turnout machines such as Kato Unitrack, AristoCraft, or LGB.Closed for static output mode to operate slow motion (stall motor) type turnouts such as Tortoise or Switchmaster.

"Turnout" is a civil engineering term for what railroaders call a "switch".  In the model railroad environment, we often use the word turnout to avoid confusion with the electrical term "switch".  On the railroad, throwing a switch usually only means one thing, while "Throw the switch" on a model railroad could mean operating a light switch.Probably the best answer is to consistently use one type of turnout.  The notion of a "DCC Friendly" turnout is a myth; the standard answer in the past has been: "If it worked on DC it will work on DCC". In the end, which turnout ...

Connecting BD1 to a DS54, DS64 and SE8c? The BD1, block occupancy detector (replaced in 2004 by the BD4) was designed as an add-on device, which took advantage of the block occupancy message generating (over the LocoNet) capabilities of the DS54. The BD1 is also compatible, for the same purpose, with the DS64 and SE8c. The following diagrams indicated how to connect the BD1 to the rails, rail power source, and the Digitrax DS54, DS64 and SE8c.  Note: The wires that connect the BD1 to the rails and rail power source are characterized as two heavy, uninsulated, and polarity neutral wires.

Athearn Genesis SD70s came factory equipped with a Digitrax designed light board. The board is NOT a DCC decoder. If you want to add a decoder and have alternating ditch lights the following steps are recommended: 1 - Remove locomotive shell; 2 - Remove dummy nine pin plug from wire harness and insert Digitrax DH163D on the harness; 3 - Remove the wires of one of the ditch light bulbs from F1N and F1P and solder them to F2N and F2P; 4 - Program CV51 to 106, CV52 to 107 and CV63 to 40. 5 - Reinstall locomotive shell.F2 on ...

The changing of the value in the CV of a DS54 is relatively easy if you follow the steps listed below. The difficult part is deciding which CV and CV value to program to achieve the desired effect. The following are step-by-step instructions for changing a DS54 configuration variable using a DT300 throttle: 1) Disconnect the DS54 from LocoNet, the auxiliary power supply, all inputs and all outputs. 2) Short the pins of the Enable Link. (see related article) 3) Connect the DS54 track inputs to the command station programming track. 4) Connect the yellow feedback adapter wire from any DS54 output (A, ...

The installation instructions indicate that a PS14 be used to power the PM42. Is it necessary that I cut the wire from the PS14 so that is can be attached it to the 44-pin connector, or is there a male adapter available for the connection? Yes, currently you will need to cut the wire, strip the ends and solder them to the edge connector of the PM42. Please see the related articles below. Which lead from the PS14 is to be soldered to terminal 3 on the 44-pin connector and which is to be soldered to terminal C? The PM42 ...

Steps needed for the DZ125PS or DZ143PS decoder installation: Remove couplers and carefully remove loco shell to reveal the 8 pin dummy (DC) plug. Remove 8 pin dummy (DC) plug [picture shown with plug removed]. Plug in the DZ125PS or DZ143PS with orange wired #1 pin in pin with triangle marked pin. Detail of DZ125PS or DZ143PS with orange wired #1 pin correctly oriented. Tuck decoder in cab area of loco, replace shell and reinstall couplers.

To Test LocoNet Cables With an LT11. Unplug the wire harness from the LT1.2. Plug one end of the LocoNet cable you want to test into the LT1.Note: When making your own LocoNet Cables, it is important to make them in a consistent manner. At Digitrax, the white wire is always on the right side of the plug when the plug is viewed with the clip at the top.3. Connect the other end of the LocoNet Cable being tested to any powered Digitrax Booster’s LocoNet Port A or B. Be sure you have at least one Digitrax throttle plugged in ...

DS64 Quad Stationary Decoder      The DS64 is a Stationary Decoder for use with 4 slow motion, solenoid, or bi-polar turnout machines Simple to hook up and configure   Controls 4 individual turnout machines: EITHER4 Slow motion turnout machines, such as TortoiseTM by Circuitron or SwitchmasterTMOR4 Solenoid-type turnout machines such as three wire (twin coil type) Peco or Atlas Snap Switches or two wire bi-polar type turnout machines such as Kato Unitrack, AristoCraft, or LGB turnouts with capacitive discharge capability  Support for up to 8 routes   Screw terminals make installation easy   Use with any LocoNet Compatible System   ...

These instructions will get you up and running quickly. A full description of all controls and technical reference information are included later in this section of the Tech Support Depot. This section assumes that you are using a new set straight out of the box. If your set is radio equipped, we recommend that you follow this quick start guide without using radio to learn the basics. When you are successfully running your radio throttle tethered to the system, then go to the DT400 series tetherless overview article to learn how to install the radio option. Connect the DB150 to the ...

I have a DH165AO decoder and Sound Bug and am installing the decoders into an Athearn SD70 Locomotive.The motor controller works and the sound as well. However, I am unable to get the lights to work. I connected the wire leads exactly as they where on the Athearn light board. Athearn uses twin forward and rear 1.5 volt lights yet the DH165AO will not power the bulbs. It will power one bulb at either end but not two. The single bulb setup glows very brightly but for a short time. So I tried using the 47 ohm resistor in parallel ...

Good DCC practice means good planning for the electrical needs of the railroad. Here, we talk about the power needs of the Texas & Southwestern. Anticipating Power Consumption The core of the Texas & Southwestern's DCC control system will be the DCS50 Zephyr, which is very appropriate for a small railroad. Zephyr has 10 "slots", memory locations in the command station each holding an active decoder address. Rated at 2.5 Amps, the Zephyr should also be enough to handle the power needs of the railroad, but if more power is needed, then T&SW can easily be expanded with an additional booster ...

Q:  I have a Digitrax Chief system. I wired the programming track as per the manual, using PROGA and PROGB outputs on the DCS100. I turned on the system and checked the track voltage with a Tony Trains RRamp meter, the mainline read 14.2 volts. The programing track did not read anything. I then checked the two wires coming from the DCS100 and they did not have any readable signal. A:  The programing track connected to PROG A and PROG B will NEVER have track power on except the very instant the program message is sent.  So, you would not ...

Connecting a turntable to a DCC model railroad is easy.  Each of the tracks approaching the rotating turntable bridge should be wired with the same orientation.  The power feeds through a pair of conductive rings to a pair of electrically conductive brushes that are wired to the rails of the turntable bridge.  DCC power is fed to the turntable bridge through an AR1 Autoreverser; when a locomotive enters or leaves the turntable bridge, the AR1 properly orients the DCC signal.  Some turntable designs have a "split-ring" electrical pickup, where the two electrical contacts that power the two rails on the ...

Digitrax DCS210+ Options switches: These documented Option Switches are implemented and tested option settings.  It is recommended that any undocumented option switches not be changed from the Factory Defaults (OPSW40=c) values to avoid unpredictable behavior. Option switches are an advanced topic, and most factory defaults work well for most layouts. OPSW# Name State Default Opsw2 DisableCS c= disable CS - Booster only   t Opsw3 Auto Reverse c= enable Booster reverser t Opsw6 Skip_Ptrk_Imin c= ignore empty Program track           t Opsw13 Purge long     c= extended PURGE time t Opsw14 Purge Off c= disable PURGING function t ...

Many clubs use a DCS100/200 as a Booster in their setups.  Digitrax does not recommend using a DCS100/200 as a Booster only for this type of setup.  If you decide to do so, please keep this information in mind:   The DCS100/200 configuration is stored in memory that uses a CR2032 battery.  Over time the battery can get weak and the DCS100/200 will loose its ability to store its configuration.  When this happens, the DCS100/200 will sound 7 beeps at power up.  It will also revert back to its factory settings and once again become a Command Station.  Since LocoNet ...

Q:  How can the DS54 be configured to control a Flashing Crossing Signal? A:  The elements necessary to create a simple function flashing/blinking crossing signal are: a block occupancy detection (trigger) device, an electronic flashing/blinking circuit (DS54) and a crossing signal. The DS54 can accommodate two different types of triggering devices: Digitrax block occupancy devices (BD1 and BD4) and third party block occupancy devices (such as magnets and reed contacts). The following drawings indicate how to connect the two different types of triggering devices, along with the crossing signal, to the DS54. The upper drawing is for the BD1 or ...

DH165K1A Board Replacement Decoder Fits Kato SD40-2, AC4400 1. Carefully remove the locomotive’s shell from the frame. Note the orientation for proper reinstallation (Figure 1). 2. Remove the four track power pickup wires clipped to the lightboard at mid point (Figure 1). 3. Unscrew the two screws securing the lightboard and lift it from the frame. (Figure 2) 4. Remove the lightboard by pulling it gently straight up, off the motor clips. (Figure 3) 5. Decoder installation is the reverse of what we’ve done so far. Snap the decoder into place over the motor clips. Be sure motor clips are ...

1) Connect the Red and Black track wires from the 9 pin Track and Function harness to the locomotive track power connections.2) Connect the function leads that are to be used from the 9pin Track and Function harness. Note that to be able to readback Sound FX CV's a combination of function lead loads of at least 60mA at 12volts should be connected to these function leads. Insulate the unused function leads so they cannot short to the locomotive frame or track power.3) Mount the 28mm speaker attached to the 10pin sound feature harness in an appropriate sound enclosure. Be ...

DH165L0 fits Life-Like GP7, SD60 and many other locos with Life-Like DCC medium plug arrangement. 1. Remove locomotive shell, noting the orientation of the circuit board inside. (See Figure 1) 2. Unplug the the manufacturer’s DCC socket from the pins on the factory board. Remove the two screws that hold the board in place. (See Figure 2) Lift out the factory board and save the two screws for future use. 3. Insert the locomotive’s DCC socket onto the pins on the Digitrax DH165L0 decoder board. In this orientation, Pin 1 (the orange wire) is the lower left pin and Pin ...

'It is possible to operate one conventional DC locomotive at Address 00.  In many cases, this is the first locomotive that beginners use when they first get their command control system.  In other cases, this locomotive is one which cannot be easily converted to DCC.  Regardless, although it is possible to use your Digitrax system in this way, it is not a recommended approach.1. Place an analog locomotive (one without a decoder) on your layout.  While the analog loco is sitting still, you will hear the characteristic “singing” caused by the DCC track signal when it is applied to analog ...

You can automate grade crossing signal lights with block occupancy sensors. Install a BD4 to detect track occupancy as shown in the figure below. Other than removing the Op Sw35 commands from the routes used in the related article example, there is no additional programming needed for the DS64. Sensor operated occupancy detection requires that all rolling stock be equipped with resistor wheels for proper detection or that the detection section is longer on each side of the RR Crossing than the full length of a train since only the locomotive will draw current. A lighted caboose on the end of ...

Q:  What is the white wire for on the SoundBug? A:  The white wire is used on conjunction with a driver cam for steam sound synchronization. Q: What type/size loco does "generic" steam sound represent? A:  This sound was based on recordings of Union Pacific 3985, a 4-6-6-4 "Challenger" type.  Q:  Does the Sound bug come with an oval speaker to fit in the shell of the older model GPs or SDs that do not have space in the fuel tank. A:  The SoundBug comes with a 28mm round speaker but others may be substituted. The included-speaker is rated at ...

  Duplex Radio Throttle do not need to be plugged in to LocoNet to Program Decoders.  Simplex Radio & Infrared throttles must be plugged in to LocoNet to program CVs on the programming track. Ops Mode Programming can be done without plugging radio throttles in to LocoNet. IR throttles must be plugged in for Ops Mode Programming. 1. Be sure that only the loco you want to program is on the programming track. If you are using operations mode programming, the loco you want to program can be anywhere on the layout but it must have a decoder that is ...

I have an older Rivarossi Heisler that I have just installed a decoder in. I have 2 other Rivarossi engines, older, with decoders in them and they work. I use them as a template. Anyway, I can't get the Heisler to run. I have the orange wire at one side of the motor and the gray at the other. The red is soldered to the frame and the black is connected to the front screw where I disconnected the light etc. I just soldered the wires together. The motor is OUT of the frame so no short can happen. Can you ...

DN163A0 is a board replacement decoder for Atlas N-Scale GP40-2, GP38 U25B, SD35, Trainmaster, B23-7 and several others. Shown here is an installation in a GP40-2. 1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the light board inside so that you can install the decoder in the same orientation. 2. Carefully remove the plastic light shroud at the front of the loco and loosen the frame screws enough to allow the removal of the light board. Lift the board out of the frame. 3. Install the decoder, square CPU to the top, between the frame ...

Photo Courtesy Kato, USA Installation Instructions: The DN143K2 cannot be tested prior to installation in the rail diesel car. 1. Carefully remove the shell from the RDC. Carefully remove the plastic casting from the bottom side of the RDC frame, using a flat bladed screwdriver to pry it loose. 2. Gently remove the white clip that holds the seat panel in place. Remove the seat panel by pushing up gently from the bottom of the frame. The seat panel has clips underneath that are very easy to break, so be careful. 3. Take extra care to notice how the RDC ...

Digitrax Query Mode: The new generation of Digitrax Advanced Command Stations and other new products from ~October 2016 onwards include some convenient new self-diagnostic and external diagnostic capabilities and methods, to help keep LocoNet systems and devices healthy and working optimally, without requiring additional tools. The DCS240 and DCS210 Advanced Command Stations include “Query Mode” diagnostic information that can be interrogated or read-out using enhanced capabilities of DT500 throttles. Advanced Command Station Query information is grouped into six broad groups of data/diagnostic information displayable by a DT500/DT500D: “Lnt”: LocoNet Device Type/product info “ELE”: Device Electrical information, voltages/currents, etc. “Lnt”: LocoNet ...

The image above shows the “M-10000 Coach Car B” for the N scale Con-Cor M-10000, which is the 1st car behind the loco. If you look closely, you can see the holes in the underbody, above which a speaker can be mounted for a sound decoder installation. The recommended Digitrax sound decoder would be the Digitrax SFX0416, but to use this decoder, one or more of the seat sections as shown below will need to be removed. There is a pocket that is designed for a speaker above the underbelly and under the center section of seats. The speaker that comes with ...

I have a Zephyr and a DB150. How can I wire the two together so that the Zephyr acts as throttle and the DB150 supplies power? At this this time I have only a single block. The easiest way to handle this situation is to divide the railroad up into two power districts. If one command station unit is more powerful than the other, then the area controlled by the weaker unit (in this case, the 2.5 Amp Zephyr) could simply be a single siding or engine terminal. The Zephyr would then become a booster, supplying power to this small ...

I have had a Digitrax Big Boy for many years I recently bought a steam loco equipped with a Soundtraxx decoder I have been able to utilize function keys 0-4 but there is quite a few more that the decoder is capable that I don't know how to access example f6-9 Production of Big Boy was from 1994 to 1998. It was superseded by other starter sets and command stations. Big Boy can access Functions 1, 2, 3 and 4, but no higher. To reach the higher function numbers will require upgrading to a more current command station and throttle ...

I bought 2 DN163I1A and 2 DN163I1B decoders which have brass . My 4 Inter Mountain FT units do not have brass motor contacts (as I found too late on your DN163I1C documentation for F3 units) but rather 2 wires soldered to the original board. Also, the DN163I1A or B can't be fitted in the space provided on the engine not only because the brass contacts on the decoder get in the way but because on the size of the decoder board is a little too big. Will all above render the decoders useless or what should I do? Because ...

Q:  I have a DH163D decoder. How do I program it so the Mars light works? A:  Any function output on Digitrax FX decoders can be set up for any FX effect by programming its associated FX CV to the appropriate FX CV value. For example, if CV52 (the FX CV for F2), is programmed with a CV value of 034, the violet wire F2 function output will be a Mars light when F2 is turned on for this decoder address and the decoder's direction is forward.

The DS64's approximate size:12cm (length) x 8.8cm (width) x 3.5cm (height)4.75" (length) x 3.5" (width) x 1.4" (height)The front edge of the DS64 needs clearance for wires to be attached.  The back edge has two LocoNet connectors and a barrel style power supply connector.  The back edge and left end have cooling slots which must remain clear.  The case has three holes which can be used for mounting screws. (#6 5/8" or longer screws can be used)

The AR1 is usually located close to the point where the gaps are cut for the reversing loop. The length of the reversing loop is determined by the maximum length of the train that will use the loop.1. Turn off track power. (Note: Failure to turn off power before connecting your AR1 may damage your AR1.)2. Connect Track Power from Rail A and Rail B mainline to the AR1. Rail A connects to terminal 5 and Rail B connects to terminal 4.3. Connect the wires from the reversing section to terminals 1 & 2 on the AR1. (Note: terminal 3 ...

Three Step Speed Table CV02 V-Start (Start Voltage) CV06 V-Mid (Mid Point Voltage) CV05 V-Max (Maximum Voltage)When you are using a throttle to control a locomotive, you will notice that as you increase and decrease the speed, the loco responds to the change in throttle settings according to the relationship between motor voltage applied and the throttle setting. This is called the throttle response curve. Decoders are shipped from the factory with a linear throttle response curve. This means that as you increase the throttle setting from 0 to full speed, the loco will look like the default curve in ...

Previously, we have recommended RJ12 connectors for LocoNet cables. While there have been online sources such as Digi-Key, Mouser and others, they have become harder to find locally. There now appears to be a easily available alternative. Many national big-box home improvement stores have RJ11 6P6C meaning they are 6 position 6 conductor and can be used as RJ12 although labeled as RJ11. These must not be confused with four conductor connectors since LocoNet has six conductors. You will need the connectors, the six-wire flat cable and a crimping tool. We paid $20.00 in February, 2008, for such a tool ...

Hook up for slow motion type turnout machines & crossing gates.Note: Multiple turnout machines of the same type can be operated on a single DS64 output.For example, you can run 2 Tortoise or Switchmaster machines on a single DS64 output.Note: If you find that your turnout is operating “backwards” simply switch the + & - wire connections to achieve correct operation.Note:  The outputs can be configured to drive a grade crossing signal.  See Knowledge Base article.

Remove the 8 pin dummy plug from Lifelike Proto 2000 light board.Before installing the decoder in the locomotive, unsolder the yellow wire from pin 2 and re-solder it to pin 3 (empty pin) on the decoder harness plug board.  We strongly recommend that you mark the decoder and/or harness so that you will remember that you have modified it.  If you use the decoder and/or harness modified in this manner in a different locomotive, your lights will not work correctly. Plug the decoder and harness into the light board in the locomotive.Program CVs as follows:  CV33 = 001, CV34 = ...

Q: I have the original DCS100 with the old style non-removable wire connectors. What would I gain with a firmware upgrade? A: Early DCS100s that do not access Functions 9 - 12. If you have a DCS100 that you would like to have updated, please send it to the Digitrax Repair Department for updating. This update is a chip change only and the original style connectors will not be changed to the new style connectors. The circuit boards used for the two different connectors are completely different and are not interchangeable. The DCS100 must be sent to us for this ...

  Setting up DS54 for Standard Turnout Reporting The creation of a feedback circuit for standard turnout reporting is simple. Connect a normally open set of contracts attached to the switch machine, a normally open set of contacts of a micro switch monitoring the turnout throw arm, or the normally open contacts of a relay monitoring the switch machine to the common (green) and switch (red) wires to the desired DS54 output circuit. The following two diagrams indicated the two most common switch machine configurations plus the contact configuration for turnout reporting.  Note: The location and type of contacts available for ...

Wired Mobile Decoder with SoundFX™+Accessory type functions for most HO scale Locomotives. The sound project loaded into this decoder may be operated independently of any other DCC motor or function decoder. If another non-Sound FX compatible DCC decoder is connected to the track leads, then CV readback of SFX0416 Sound CV's and PR3 SoundTest modes may not be possible. Note that it is always possible to Write CV values using Operations mode or a Service Mode programming track, even if CV Read is inoperative. If the connected function loads are insufficient for CV readback with a PR3 or an incompatible ...

Can I use the DS64 to power frogs in Atlas turnouts with solenoid ( code 83 ) type switch machines? No, the DS64 does not have internal contacts to provide power to the frogs. This could be done by using a switch machine with its own contacts; these have been made by NJ International, Tenshodo, PFM and others. Another alternative would be to use the Atlas Snap Relay. The Snap Relay is a solenoid device like the switch machine, but instead of throwing the turnout, it throws a set of electrical contacts. The relay is wired in parallel to the switch machine, ...

The actual track voltage supplied by the DB200 can be adjusted. To adjust the track voltage, you must open the DB200 case (this will not void your warranty). 1. Remove the DB200 input power & disconnect all DB200 leads. 2. Remove the two screws on the top and bottom of each side of the case. 3. Slide the gray front panel off the DB200. 4. Be careful to avoid disturbing components other than the ones described below. 5. Locate the small yellow trimmer potentiometer behind the LocoNet B Jack and Scale Switch. 6. Use a small screwdriver to turn the ...

  There are two methods of providing power to the DS54: from the rails and from an auxiliary power source. The DS54 can be powered from the rails however, Digitrax strongly recommens that the DS54 be powered from an auxiliary power supply capable of delivering 12-16 volts (ac or dc) at 300 millamperes for best results.  Powering the DS54 from the rails reduces the current available to power locomotives and lighted rolling stock.  The auxiliary power supply connections are the red (+) and black (-) wires. Note: Digitrax recommends the PS14 Power Supply for independently powered DS54’s. Multiple DS54’s can be powered from a single power ...

One special feature on the Texas & Southwestern is a built-in programming track. The programming track is located in a short section of track in the small engine terminal of the T&SW. This track has both rails insulated from the rest of the railroad. It uses a Double Pole Double Throw (DPDT) toggle switch to select what purpose this section of track is used for. When the toggle switch is set in one direction, the track has DCC power on it. When the toggle switch is aligned in the other direction, the track is now connected to the programming terminals ...

Sound Decoder:  SDH164D SoundFX Wired Mobile Decoder for HO Locomotives Master Volume: CV58=9 to 15, Diesel CV60=1, Bell CV141=64 Max., Horn CV142=64 Max. Speaker: one SP26158B Rectangular 26.5mm x 15.5mm x 9mm, 8Ohms 0.5W Compact Box Speaker with enclsure & wires A 5 Ohm 1/2W resistor in series with the speaker.              Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     67 15  4.00   65 15  4.15   67 15 4.15   ...

Installation of the SFX004/SFX006 SoundBugs into a DH165-Series decoder is easy, but it does require some care. The SoundBug must be properly oriented to the decoder. Here, the DH165L0: Here, an installation in a Proto1000 DL-109. In this orientation, the SoundBug sockets are to the right on the DH165L0 decoder: The SoundBug is plugged into the sockets of the DH165L0 decoder: Because the DL-109 is a diesel locomotive, it will not need the white synchronization wire. Everything is fitted into place. The SoundBug is shipped with a small piece of foam to protect the pins of this decoder. You may ...

I have many many loco's. How do I determine which mobile decoder to select for each one? First, modelers with many locomotives often become bewildered at the prospect of converting all of their locomotives to DCC. Take it one step at a time. Consider that you are not operating all of those locomotives at the same time; start by gradually converting your locomotives, beginning with your favorites. Digitrax maintains a list of suggested decoders for specific locomotives on our website.  The Digitrax Decoder Selector can be found here: http://www.digitrax.com/products/engine-matrix/decoderJust because your particular locomotive is not listed does not mean that ...

BDL168 Pin Out Configuration: Notes: 1) All connector pins are paired top (component side of the BDL168) and bottom (solder side of the BDL168) except 11/M and 12/N. For 6 Amp current rating with 3 Amp connector pins, track/zone wires must be connected to both pin pairs: e.g. Zone A = pins 1 & A (See Figure below): 2) Letters G, I, O & Q are not used as pin designations on the connector. 3) Power connections should be made to a power supply dedicated to BDL168 use only. Multiple BDL168 units can be supplied by a single shared supply ...

Join Your Throttle to the Duplex Group 1. Connect a DT402D Duplex Radio Throttle with an installed battery to the front RJ12 jack of the UR92 for about 2 seconds. 2. Disconnect the DT402D from the LocoNet jack. The DT402D will briefly display an 8 character Duplex Group name and the Channel number being used by the UR92 Group. The actual Duplex Group name is not important at this point, it is simply used by the DT402D to join this Duplex group on its particular Duplex channel (#11 through #26). 3. Now that the DT402D has joined the Duplex group, ...

1. Carefully remove the locomotive’s shell from the frame. Notice the orientation of the shell to the frame (Figure 1) so that you can reinstall the shell correctly. 2. Remove the dummy plug from the locomotive’s DCC-ready socket. (Figure 2) The jumper plug allows the loco to operate on a standard DC track or in analog mode on a DCC track. Pin 1 is marked for proper orientation of the decoder. 3. The DZ125PS has a short, 1" harness with a DCC 8-pin plug on the end of it. The plug is oriented so the pin for the orange wire ...

1. Disconnect the wire harness from the LT1.2. Plug one end of the LocoNet cable being tested into the LT1.3. Connect the other end to the cable into on of the LocoNet ports on your DCS50. Make sure the Track Status Indicator Dot is lit.4. All four LEDs on the LT1 will light if the cable is good. LEDs may not all be the same brightness, this is normal. NOTE: Only three LEDs will light if the Track Status Indicator Dot is not lit.5. If any of the LEDs fail to light, recrimp the plugs on the LocoNet cable and ...

Q:  I have an HO Bachmann Alaska EMD GP40 (Bachmann item #63548) that I have kept in the box for about a year. I recently received a Digitrax Zephyr and I want to put a decoder in the locomotive. I used your reference guide and did not see it listed. Does that mean it's not available? A:  There are many reasons why a particular locomotive is not listed in our database.  The most common is that we have never been asked about that particular model.  There are so many new models it is a difficult task to keep up with ...

The Kato 4-8-4 FEF Steam Locomotive accepts the DN163K4A board replacement decoder. To disassemble the Kato 4-8-4 FEF, perform the following steps:   1. Gently slide the cab towards the tender.   2. Using a small Phillips head screwdriver, remove the screw located at the rear of the locomotive.   3. Slide the boiler toward the front of the locomotive.   4. Lift the entire boiler assembly off the chassis   5. Remove the plasic clip which is covering the analog circuit board.   6. Carefully remove both of the motor power tabs from the analog circuit board, being careful ...

Decoders with FX function features have 4 user configurable, independent special effects generators. All current production Digitrax Decoders use FX3 functions so this article is not applicapable to these decoders. CAUTION: Decoders with FX3 function generators use different CVs to control the decoder outputs. All current production Digitrax decoders use FX3 function CVs. Before using these CVs to program your decoders make sure that they are FX and not FX3 decoders.The Real FX effects are set up by programming CV values as described below.F1/F2 NOTE: If using DH142, DN142, DN141K2, DN149K2 series decoder, when F1 is set up for FX, ...

The Trix GG-1 is a fine die cast locomotive model which is equipped with a sound decoder. As produced by the Trix factory in Germany, the sound functions are: F0 Normal headlights F1 Bright headlights F2 Cab lights F3 Sound of main relay F4 Low speed switching range (switching acceleration / braking delay off) F5 Bell F6 Horn, continuous blast F7 Sound of pantograph being raised and making contact with the wire F8 Sound of blower motor F9 Sound of switching relays F10 Sound of cab radio F11 Sound of couplers F12 Sound of clickety clack railroad track Digitrax operators ...

At the factory, your DS64 was set to control solenoid type turnout machines that use a single pulse output for operation. If you are using slow motion turnout machines, like the Tortoise or Switchmaster, that need a static type output to operate, you’ll need to reconfigure the DS64’s outputs before hooking up your turnouts.To set up your DS64 to operate stall motor type turnouts:1. Connect the DS64’s ‘TRKA’ and ‘TRKB’ terminals to your track. No turnouts should be connected to the DS64 at this time.2. On the DS64 press and hold the OPS button down for about 3 seconds until ...

The DH165Q1 fits many Atlas, Intermountain, Life-Like & Other factory sound equipped HO locomotives. Installation Instructions - Intermountain F7 example: Removing Locomotive Shell and Disconnecting Lightboard 1. Carefully remove the front coupler and then the locomotive's shell from the frame. Note the orientation for proper reinstallation. 2. Unplug and mark the two track power pickup 2-pin plugs, the motor 2-pin plug and the 6-pin headlight plug(Figure 1) Observe and carefully note the original wire locations! One of the track power plugs and the 2 pin motor plug can be inadvertently swapped when hooking up the new decoder PCB. 3. Unscrew ...

CV133 and CV134 work together to control chuff timing. CV133 and CV134 can be adjusted to create the desired chuff rate in your locomotive, or you can configure your sound decoder with CV133 and CV134 to use an external cam to create chuffing sounds. CV133 Steam Chuff/CAM configurations: CV 133 set to a value between 1-127 determines the driver size in inches. (Default Value = 63) CV134 Steam gear ratio trim CV 134 set to a value of 32=100% ratio. Setting CV133's value from 1-127, puts the sound decoder into 'Autochuff' mode. Autochuff mode tells the decoder to simulate driver ...

I have an extensive collection of older (15-20 years) Z-Scale Maerklin equipment. Can I convert the locos to Digitrax, or must I buy some other brand of loco to use Digitrax? Maybe yes, maybe no. It depends upon the size of the locomotive. We are aware of several European Z-Scale model railroads that use Digitrax. We also know of a very large Z-Scale railroad in Washington, DC that uses Digitrax. This particular railroad is a model of Swiss prototype, so the locomotives are all electric-types; there seems to be enough room inside for a decoder, especially the new DZ125 series ...

I'm trying to install a DH123D decoder in a Life like P2K PA loco and make the mars light work. HELP! Because the DH123D is a two-function decoder (front headlight, rear headlight), it may not be the best decoder choice for this locomotive. In practice, some PA's had only one headlight, thus there would be no Mars light. The DH123D would be an appropriate choice for those locomotives. Typically, eastern railroads would just have one headlight; think Pennsy and Southern Railway. Western railroads, because of higher train speeds, often used warning lights such as the Mars Light or Pyle Gyra-Light; ...

Q:  As an HOn3 advocate and new to DCC with early PFM engines (2-6-0 & 2-8-0 motors in tender and some smaller ones) what would be the suggested decoder (am not sure am identifying the part correctly) that would be used in these engines? All I have seen so far identifies items used in H0 standard gauge. A:  Digitrax has many happy Narrow Gauge customers.  You'll need to consider three things to join their ranks.1.  The physical size of the decoder, because narrow gauge engines are smaller than Standard Gauge locomotives. Since your space is limited, using smaller decoders is the solution. Digitrax ...

My son & I have PROTO 1000 Diesel EMD F3A-B Sets. The powered locos are equipped with an eight-pin plug for easy decoder installation. Our problem is that we've been looking through books & have no idea what sound card & speakers we are going to need that corresponds with these type of locomotives. I was told that they would need sound cards that are from the "Early Diesel" era. If this is true, please tell me what sound cards,speakers & wires do we need to make this happen? We are fond of F-units, and the Proto 1000 F-units are ...

Setting up your new Zephyr: Unpack the DCS-50 command station and the PS-315 power supply. On the back of the DCS-50,locate the gray screw terminal strip.On this strip, locate the two terminals labeled “RAIL A “and “RAIL B”.Attach these terminals to your track wires.It does not matter which is which. Before proceeding to the next step,make sure the throttle knob [1] is turned all the way to “stop” and the direction/brake lever [2] is set to”brake”. [See photo blelow]. Now, find the plug on the back of the DCS-50 marked “POWER IN, 15 VAC, 2.5 AMPS”. This is where you ...

What do I need for DCC control of a Walters Cornerstone Swing bridge? Image Courtesy Wm. K. Walthers We do not have any direct experience with this particular bridge but after a little research, this is what we recommend.The instruction sheet which comes with the 933-1050 Motorizing Kit is quite vague.  "The unit runs on DC power.  Hook the wires up to the DC contacts on a transformer with a maximum voltage of 12.  If you hook it up to a variable speed transformer, do not exceed 12 volts.  The gear ratio is 320:1."  That said, it is still a ...

Application Note: Steps needed for installing the DN143IP mobile decoder into the Con-Cor N-Scale Aerotrain "DCC Car". The image above shows the “DCC Car” for the N scale Con-Cor Aerotrain, which is the 1st car behind the loco. It shows the holes in the underbody, above which a speaker can be mounted for a sound decoder installation. The recommended Digitrax sound decoder would be our SFX0416, but to use this decoder the seats will need to be removed. There is a pocket that is 16mm wide, 36mm long and 3mm deep designed for a speaker above the underbelly and under ...

As originally conceived, the Texas & Southwestern was set up with a very simple DCC system. The railroad uses a DCS50 Zephyr as its command station and booster. The Zephyr is connected to a central power bus, and all tracks, stationary turnout decoders and the automated reverse loop unit are connected to it. Likewise, the LocoNet connections are a series of simple cable connections starting at the Zephyr and ending at the last Universal Panel. The T&SW works well with this arrangement, but there are additional devices that will enhance the operation of this railroad. Digitrax PM42 Power Management System ...

CV29 is called the configuration register. It controls the following decoder characteristics: 1.  Whether the decoder uses 14 speed steps, 28/128 speed steps or loadable speed tables.  This affects how smoothly the loco will move and how it responds to throttle controls.2.  Whether the decoder automatically converts to analog mode when no DCC signal is present.  This allows the decoder to operate on a DC layout even though it is DCC equipped.3.  Defines the normal direction of travel for the locomotive. Normal Direction of Travel or NDOT can be changed when the motor connections of decoder have not been connected so that the locomotive runs ...

Some Digitrax decoders offer scalable speed stabilization (also called back EMF) control to help smooth out operation in the low end of the speed range.  This feature can be beneficial especially in N scale switching situations especially when the decoder can select how much of this effect to implement (scalable speed stabilization).  Speed stabilization is a decoder feature that can be used with any DCC system.  Most Digitrax decoders that support this feature are shipped with scalable speed stabilization turned off so, to use it you will need to set program them to use this feature.  Other Digitrax decoders are ...

Note the SFX006 is identical.  These instructions pertain to both Soundbugs.   1) Identify the correct orientation and mounting side of the DH165 series Decoder with SFX004 Soundbug Socket to plug this sound module into. There is text saying "SFX here" etc,. The SFX004 must only be mounted from the correct side and orientation, for each of the DH165 host decoders. 2) With correct orientation noted from step 1, align the dual row of SFX004 connector pins to the matching holes in the DH165 host PCB. Apply gentle and firm pressure behind the SFX004 connector to engage the pins until ...

Q:  Is it possible to use Digitrax equipment to wire the Kato N-Scale Automatic Track Crossing? If so, how do I do it? A:  The answer is a probable "No", but there may be a workaround. The Kato, USA website notes: Some Unitrack components such as the Automatic Crossing Gate and 3-Color Signal were designed with DC operation only. So, the official position is that that these devices don't work in the DCC environment. However, we are not above speculating on how to do this, nor are others. An online web search turned up this bit of message traffic by ...

Sound Decoder:  SDH164D SoundFX Wired Mobile Decoder for HO Locomotives Master Volume: CV58=9 to 15, Diesel CV60=1, Bell CV141=64 Max., Horn CV142=64 Max.   Speaker: Two SP26158B Rectangular 26.5mm x 15.5mm x 9mm, 8 Ohms 0.5W Compact Box, Speaker with enclosure & wires.  Speakers are wired in series.              Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     67 15  4.20   66 15  4.30   67 15 4.30   3.05 Vrms   ...

Digitrax SoundFX Decoder Troubleshooting Guide This troubleshooting guide assumes that you are working with an operating Digitrax system that is able to run trains and that the locomotive you are troubleshooting is operational and has a Digitrax sound decoder and speaker installed correctly.  If there is no sound, first make sure the decoder is not muted: Press the Function 8 (F8) key, and make sure F8 is OFF.  Function 8 is used to toggle between sound active (F8 OFF) and mute (F8 ON). If there is no sound and the locomotive won’t move when the address is selected on your ...

LNWI Advanced Options Status LEDs: The LNWI has two status LEDS Green ID indicator and a Red OPS indicator.  The state of these indicators can be interpreted to provide status information and also some useful diagnostic insights. Table 1: Status LEDs LED Status Indicates Green ID indicator mostly lit, winking OFF every 3 seconds LNWI is powered and connected to LocoNet Green ID indicator mostly off, blinking ON every 3 seconds LNWI is powered and LocoNet is not connected or sleeping Green ID indicator winks OFF LNWI received a good LocoNet Message Red OPS indicator blinks ON LNWI received a ...

  Option switches are used to change the operation of the DB150. Option Switch # Effect on system when Option Switch “c” closed Default OpSw 02 Booster Only override t OpSw 03 DB150’s booster is auto reversing t OpSw 05 Default closed for command station –DO NOT CHANGE- c OpSw 13 Loco purge time extended from 200 seconds to 600 seconds t OpSw 14 Loco purging is disabled t OpSw 15 Purging will force loco to Stop or 0 speed t OpSw 17 Automatic advanced decoder assisted [FX] consists are disabled c OpSw 18 Extend the DB150 booster short circuit ...

Series 4 decoders like the SDH164k1's will conform to the 10-pin wiring diagram   Function pads for F1 and F2 are located on the SDH164K1 boards on opposite sides by the front headlight. Functions 3 and 4 are located on the 10-pin wire harness, with the Brown wire being the F3 negative and the Yellow wire being the F4 negative.  F3 and F4 functions have a common positive connection to the solder point labeled in the middle of the board.     The common LED sizes used are 3 mm and 5 mm.

Decoders with FX3 features have 8 user configurable, independent special effects generators.  All current production Digitrax Decoders use FX3 function features. These are set up by programming CV values as described below.  If your decoder is not a Series 3 decoder, please check the spec sheet to determine which type of functions it supports.FX3 functions incorporate FX generators with additional dynamic and static qualifiers.  FX3 functions are fully remappable so they can be controlled by any function key on your system.  A master light switch can be set up to turn off all lights on a locomotive. Functions associated with advanced ...

Sound Decoder:  SDH164D SoundFX Wired Mobile Decoder for HO Locomotives Master Volume CV58= 9 to 15, Diesel CV60=1, Bell CV141=64, Horn Cv142=64 Max. Speaker:  One 28mm dia. 32 Ohm 0.5W Speaker is enclosed, and is hanging by the wires.              Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     69 15  4.55   67 15  4.60   70 15 4.75   3.35 Vrms   67 12  4.35   65 12  4.55    The ...

Sound Decoder:  SDH164D SoundFX Wired Mobile Decoder for HO Locomotives   Master Volume: CV58= 9 to 15, Diesel CV60=1, Bell CV141=64 Max., Horn CV142=64Max. Speaker: One SP26158B Rectangualr 26.5mm x 15.5mm x 9mm, 8 Ohms 0.5W One SP53188B 53mm X 18mm X14mm, 8 Ohms 0.5W Speakers are wired in series.              Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     69 15  4.15   65 15  4.30   69 15 4.30   3.05 ...

Sound Decoder:  SDH164D SoundFX Wired Mobile Decoder for HO Locomotives Maste Volume: CV58=9 to 15, Diesel CV60=1, Bell CV141=64 Max., Horn CV142=64 Max. Speaker:  one SP26158B Rectangular 26.5mm X 15.5mm x 9mm, 8 Ohms 0.5W Compact Box, Speaker with enclosure & wires. A 5 Ohm 1/2W resistor in series with the speaker.              Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     68 15  4.00   65 15  4.10   68 15 4.10 ...

Sound Decoder:   SDH164D SoundFX Wired Mobile Decoder for HO Locomotives   Speaker:Two SP53188B 53mm x 18mm x 14mm 8 Ohms 0.5W  Rectangular Box These two 8 ohms are wired in series.   Master Volume: CV58= 9 to 15,   Diesel CV60 = 1, Bell CV141= 64 Max.,   Horn CV142= 64 Max.                Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     71 15  4.15   67 15  4.30   71 15 4.30   ...

Sound Decoder   SDH164D SoundFX Wired Mobile Decoder for HO Locomotives   Master Volume CV58= 9  to 15,   Diesel CV60 = 1, Bell CV141= 64 Max.,   Horn CV142=  64 Max.   Speaker:   One 28mm dia. 32 Ohm, 0.5 W Not enclosed, and is hanging by the wires.                Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     66 15  4.55   64 15  4.60   67 15 4.75   3.35 Vrms   64 ...

SDH164D SoundFX Wired Mobile Decoder for HO Locomotives Speaker:   Two 28mm dia. 32 Ohm, 0.5 W These speakers are connected in parallel. Master Volume  CV58= 9  to 15,   Diesel CV60 = 1, Bell CV141= 64 Max.,   Horn CV142=  64 Max.            Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     68 15  4.15   66 15  4.25   70 15 4.25   3.00 Vrms   67 12  4.10   65 12  4.20   Each ...

  Sound Decoder:  SDH164D SoundFX Wired Mobile Decoder fopr HO Locomotives Master Volume: CV58=9 to 15, Diesel CV60=1, Bell CV141=64Max., Horn CV142=64 Max. Speaker: 4 inch Dia. 8 Ohm Speaker, 4 Watts with a 3.3 Ohm resistor in series.              Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     79 15  3.85   74 15  4.00   79 15 4.00   2.84 Vrms   78 12  3.80   73 12  3.95   Amplifier ...

Sound Decoder:  SDH164D SoundFx Wired Mobile Decoder for HO Locomotives Master Volume: CV58=9 to 15, Diesel CV60=1, Bell CV141=64 Max., Horn CV142=64 Max. Speaker: Small-Oval 8 Ohm, 1 Watt with a 3.3 Ohm resistor in series. 35mm x 16.2mm or 36.9mm x 18.3mm w/enclosure 8.1mm High or 9.1mm w/enclosure Tonystrains see dreamspeakers              Diesel Horn         880Tone Sine Wav.     Horn & 880 Hz together   Factor     dB@4' CV58 MtoP   dB@4' CV58 MtoP   dB@4' CV58 MtoP   x 0.71     67 15  4.00   65 15  4.15   67 15 4.15   ...

Digitrax series7 mobile decoders have many industry standard Configuration Variable (CV) numbers and values, as well as numerous Digitrax custom CV numbers and definitions or controls. The series7 CV values are a superset of older Digitrax FX3 series3 and series6 decoders, already covered in Digitrax Decoder Manual V2 on the Digitrax Web site. The “CV8 to 8 default” columns indicate current factory defined value after writing a value of 8 to CV8, using; Service mode programming track or Mainline Operations Mode Write to the active decoder address. An entry with value/xx indicates a xx number invokes the value before the ...

When you are using a throttle to control a locomotive, you will notice that as you increase and decrease the speed, the loco responds to the change in throttle settings according to the relationship between motor voltage applied and the throttle setting.  This is called the throttle response curve.  Decoders are shipped from the factory with a linear throttle response curve.  This means that as you increase the throttle setting from 0 to full speed, the loco will look like the default curve in this diagram.If you want to create a more realistic throttle response curve, you can set up ...