Digitrax Products -> Digitrax Starter Sets -> Super Chief Xtra Starter Set
You are viewing all articles in Digitrax Products -> Digitrax Starter Sets -> Super Chief Xtra Starter Set (including subcategories). To further filter by subcategory, select from below.
Digitgrax refers to the throttle knob on the left side as the L Throttle and the throttle knob on the right side as the R Throttle. This corresponds to the L & R that appears on the throttle. The throttle knobs on the DT400 use “encoders.” They give very smooth, fine speed control. In 128 speed step mode it takes four complete rotations of the knob to go from stop to full speed. When you select a locomotive that is already moving on either throttle knob, that throttle will continue to run the locomotive at the same speed and in the ...
'It is possible to operate one conventional DC locomotive at Address 00. In many cases, this is the first locomotive that beginners use when they first get their command control system. In other cases, this locomotive is one which cannot be easily converted to DCC. Regardless, although it is possible to use your Digitrax system in this way, it is not a recommended approach.1. Place an analog locomotive (one without a decoder) on your layout. While the analog loco is sitting still, you will hear the characteristic “singing” caused by the DCC track signal when it is applied to analog ...
You can use your DT400 series throttle with a DCS100 or DCS200 to set up routes that are triggered by operating a single turnout address to make it either c (closed) or t (thrown). Setting up and operating routes is similar to consisting locomotives because you can cause more than one unit to operate based on a single command sent to the system. We call the turnout address that other turnout addresses are “consisted” to, the TOP address. To operate a route, use Sw (Switch) mode to select the TOP turnout address in the route and move it to either closed or ...
The DT402 & DT402's screens are an LCD (Liquid Crystal Display) that is designed to show you what you are controlling with the throttle. It also facilitates programming and other features of the LocoNet system. 1. The handheld has two throttles called the left throttle (L) and the right throttle (R).2. There are two direction indicators. One for the L throttle and one for the R Throttle. If the direction indicator is lit, and there is smoke over the loco icon there is an address selected on that throttle.3. The direction indicator with blinking smoke indicates which throttle is currently active. The ...
1. Plug the DT402 & DT400 series throttle into any functioning Digitrax LocoNet System or other LocoNet compatible system and you are ready to go! You can use any LocoNet jack on your system.2. First, you will see the DT402 or DT400 version number screen: This screen shows the throttle's software version number. It is displayed for a few seconds each time you power on the throttle.3. Next you will see the power indicator screen: This screen indicates the power available to the throttle. When you are plugged in to LocoNet, this value will be between 9 & 15 volts. When you ...
The track power indicator on your DT400 shows whether track power is on or off. If the track power indicator is lit then track power is on. There is also a Track Power indicator on your command station.To Turn Track Power On:If the Track Power Indicator is not lit, turn track power on as follows:1. Press the PWR Key2. Press the Y + Key and the Track Power Indicator on your DT400 display and on your command station will come on solid. If the Track Power Indicator is blinking, press the Y+ Key again to make it solid and turn ...
These are the basic DT400 and DT402 series throttle operating instructions designed to get you “up and running” quickly and to minimize your “frustration level” as you learn to use the throttle. Turning Track Status On and Off To run your layout you must be sure track power and track status are both ON. Follow these steps with your DT400 or DT402 series throttle to do this. Press the "PWR" key on the bottom left side of the throttle. The words “+ON -OFF” will come on in the display. Press the “Y +” key quickly and you should see the ...
Zephyr Xtra Super Empire Builder Xtra Super Chief Xtra Command Station DCS51 DB150 DCS100 Current Rating 3 Amps 5 Amps 5 Amps or 8 Amps Throttle DCS51 DT402 DT402 Throttle Controls Single Knob, Direction Switch Dual click encoder throttles Dual click encoder throttles Function Control F0-F29 F0-F29 F0-F29 Keypad Full Numeric Keypad Full Numeric Keypad Full Numeric Keypad Display Large LED Multi-line Backlit LCD Multi-line Backlit LCD Throttle Capacity 20 22 120 Loco Capacity 20 22 120 Loco Address Range 00-9000+ 00-9000+ 00-9000+ Stationary Address Range 01-999 00-999 00-999 Turnout Position Reporting Yes, last command sent Yes, last ...
Q: I have three engines lashed together. The sound is coming through . However when I turn the knob there is no response. The engine in the window is blinking and there are two stationary dots above A: If you are using a DT300 series or DT400 series throttle, make sure that the Track Status Indicator dot in the upper right of the display just below the right throttle knob is on solid. If it is not on at all Track Power is OFF. If it is blinking, Track Status is in Idle and the throttle knobls will not move the locos. To ...
I would like to know what the output voltage of PROG A & PROG B terminals should be on my DCS100 Command Station. Under normal circumstances, there will be no voltage present across PROG A & PROG B. When the DCS100 is actually programming a decoder, there will be brief bursts of voltage up to 12 Volts.
I own a Digitrax Starter Set that is now discontinued. Can I still use it and can it be upgraded?LocoNet lets you use all Digitrax LocoNet components in your system no matter when you purchased them. You can continue to use what you already own with new components as they become available. Note: This will work with all starter sets except for Challenger. If you have a Challenger Set and you want to move up, the best thing to do is to purchase one of the new sets and use the DB100 series booster that came with your Challenger as ...
Super Chief superseded Chief II.Super Chief IncludedA DT400 throttleA DCS100 Command Station BoosterA UP5 Universal PanelInstruction Sets
I want the top of the line Digitrax Set. Which one should I buy?Super Chief Extra with Duplex Radio.
Chief was superseded by Chief II, which came with a DT300 throttle.
Is it possible to use UP3 with a Super Chief system?Yes. Both have LocoNet in common, so the signals produced by the DCS100 Super Chief go though LocoNet to all devices that can connect to the LocoNet, including the UP3.
There are times, when all else has failed, that it is best to simply start over. To reset Super Chief, you can use the Chief's option switches to start fresh. *Special Instructions for DCS100 Op Switches 36, 37, 38, & 39 For Op Switch #36-#39 to work properly: In this example, a complete reset will occur (Option Switch 39). 1. Place the DCS100's MODE toggle switch on the DCS100 in the Center OP position 2. Press the SWCH key on the DT400/DT402/DT500 3. Press 3 and then press 9 4. Set the OpSw of choice to c by pressing the ...
Chief was Digitrax third commercially produced starter set. It was manufactured from 1998 to 2000. It included:A DT100 throttleA DCS100 command Station Booster