KB675 Resetting a mobile decoder to factory settings

Most Digitrax mobile decoders have a global reset function, which returns the decoder's CVs to their factory default settings.This is useful if the CV values in a particular decoder have been changed with less than wonderful results. For example, you may have accidentally set the CV value for acceleration so that the engine won't move for minutes when issued a speed command. This makes it look like the decoder is not working when all it needs is to have the CV value for acceleration reset. Many of the decoders that are sent to us for repair just need to have ...

KB46 Reset Pre-Series 3 Digitrax Mobile Decoders to Factory Defaults

Digitrax Series 3 and later mobile decoders are reset by setting CV08 to a value of 08 to reset everything or 09 to reset every thing EXCEPT the loadable speed table.Earlier Digitrax decoders require resetting each CV individually. To reset earlier Digitrax mobile decoders: Reset your decoder to the factory settings by going into program mode and manually resetting the following CVs to these values: CV01=03 CV29=06 CV03=00 CV04=00 CV02=00 CV05=00 CV06=00 If you set up loadable speed tables, you may also need to reset CV65=00 CV66=00 CV67=00 CV68-93=00 CV91=00 CV95=00    

KB846 Zephyr - Programming Mobile Decoder CV's Other Than Locomotive Addresses

There are many different CVs that have been defined to control operating characteristics of your locomotives. Your decoder manual has a complete listing of CVs that are available with specific decoders, what they do and suggested values for each CV. Programming these CVs is simple:1. Be sure that only the locomotive you want to program is on the programming track.2. Press the PROG Key to enter programming mode. The DCS50 will display one of the programming modes available. Digitrax recommends the Paged Mode when you are using the programming track. As you press the PROG Key repeatedly, you will cycle ...

KB112 Reset Procedure for Mobile Decoders

CV08 is the factory reset CV for all FX3 decoders and also the Manufacturer ID CV for all decoders. This procedure is performed on a programming track. To reset all CV values to their factory default, program CV08 to a value of 008/x08 while the locomotive is on the programming track. To reset all CV values except for 28 step speed tables to their factory values set CV08 to a value of 009/x09. Earlier Digitrax decoders must be reset manually, CV by CV. This procedure may or may not work with other manufacturer's decoders. When you "read" the value of ...

KB628 Performing factory decoder reset using Digitrax DCS100 & DT400 series throttle

Overview:To reset locomotive electronics to factory defaults the user must set CV08 to a value of 08. It is recommended that this procedure be performed on the dedicated service mode programming track using direct mode programming.* Note: This is the only programming procedure that we recommend using the programming track for. All other programming should be performed on the main track using Operations mode programming.Procedure:1. Place the DCC equipped locomotive on a dedicated service-mode programming track.* Note: The rails of this track should be connected to the PROG A & PROG B outputs on the DCS100 command station.2. Set the ...

KB629 Decoder reset to factory default settings using Digitrax Zephyr Xtra (DCS51) or Zephyr (DCS50)

Performing factory decoder reset using Digitrax Zephyr Xtra (DCS51) or Zephyr (DCS50)Overview:To reset a Digitrax decoder to factory defaults the user must set CV08 to a value of 08. It is recommended that this procedure be performed on the dedicated service mode programming track using direct mode programming.Procedure:1. Place the decoder equipped locomotive on an electrically isolated service-mode programming track which is connected to Programming Outputs Prog 'A' & 'B'.2. Press the PROG MODE key until “dir” appears in the LED display.3. Press the STEPS CV key. (The LED display should read “t###” with the # symbols replaced by actual digits)4. Enter “08” using ...